manualshive.com logo in svg

Steris Harmony LED Wall Control Unit, Operator'S Manual

Share
Download
Steris Harmony LED Wall Control Unit Operator'S Manual Download Page 46

5-18

10083002

Operator Manual

Operating Instructions

5.11  Install Camera 

Disposable Sterile 

Cover

When the lighthead is used with a camera, a disposable sterile cover 
is placed over the camera housing. Refer to 

Figure 5-15

. (Disposable 

sterile covers are available from STERIS.) Do not use the lighthead 
during a sterile procedure unless a sterile disposable cover has 
been placed on the camera. 

5.12  Video Camera 

The optional video camera is integrated into a removable, modular 
handle that can be fitted into Harmony lightheads. 

•

A high-resolution (HD) camera can only function in a lighthead 
labled for HD operation (always the lowest-position lighthead).

•

A standard-resolution (SD) camera can function in any lighthead. 

Whenever the video option is used, a separate sterile disposable 
cover must be fitted over the camera before each procedure (see 

Section 5.11, Install Camera Disposable Sterile Cover, page 5-18

). 

This cover allows the camera to be grasped and used in the same 
way as a standard handle, including positioning the lighthead for 
optimal illumination, adjusting lighthead intensity and pattern size, as 
well as positioning the video image field for the best view of the 
procedure. The sterile cover must be removed from the camera and 
discarded after each procedure.

WARNING – BIOHAZARD: 
Sterile disposable covers are 
intended for single use only.

WARNING – STERILITY 
ASSURANCE HAZARD: Do 
not use disposable handle 
covers if its packaging has 
been damaged, torn or 
opened; as the sterility of the 
cover may be compromised. 

!

!

Figure 5-15. Install Camera Disposable Sterile Cover

Summary of Contents for Harmony LED Wall Control Unit











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands