background image

INSSQBF1400607

TROUBLESHOOTING

Noisy fan

• Check ductwork 
  - Ensure that bends in the ductwork are kept to a minimum.
  - Junction between the adaptor and the duct must be airtight.
  - In the case of a flexible duct, ensure that it is not sagging.
• Elbow angles must be greater than 90 degrees.
• Ensure that the outside hood is not blocked.

Fan not working

• Check for improper electrical wiring.
• Check that circuit breaker is in the ON position.

Mounting springs do not hold the grill firmly in place

Make sure the mounting springs 
were inserted into their respective 
slots.

If the mounting springs are 
inserted into their respective 
slots and the grill does not hold 
firmly in place, then increase their 
tension by bending the 2 legs of 
each spring outward.

UL STANDARD 507 LISTED

CSA LISTED ACCORDING TO STANDARD C22.2 NO 113

LIMITED WARRANTY

This product is guaranteed for a period of 5 years. If at any time during this period the unit becomes defective, it must 
be returned to its place of purchase with a copy of the invoice, or simply contact our customer service department 
(with a copy of the invoice in hand). The warranty is limited to the factory repair or the replacement of the unit, and 
does not cover the cost of disconnection, transport, installation, and component replacement. Any damages or failures 
caused by abuse, misuse, abnormal usage, faulty installation, or improper maintenance (other than that provided by 
Stelpro) will not be covered by this warranty. Stelpro Design disclaims any responsibility for bodily injuries, losses of in-
come and material damages caused directly or indirectly by the product. Some States and provinces do not allow the 
exclusion or limitation of incidental or consequential damages and some States do not allow limitations on how long 
an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you specific 
legal rights and you may have other rights which vary from State to State and province to province.

Stelpro Design inc.
1041, Parent Street
Saint-Bruno (Quebec)
J3V 6L7

12

Summary of Contents for SQBF140













Reviews: