Stellar
®
Slider65 Owner’s Manual | Page iii
Table of Contents
Introduction iv
Serial Tag Location ...................................................................................................................................................................... v
Chapter 1 - Specifications ...............................................................................................................................................................1
Slider65 Specifications ................................................................................................................................................................ 1
Slider65 Latch Locations for Skid Compatibility ....................................................................................................................... 2
Slider65 Grease Zerk Locations .................................................................................................................................................. 2
Chapter 2 - Installation ....................................................................................................................................................................3
General Installation .................................................................................................................................................................... 3
Installer Notice ......................................................................................................................................................................... 3
Torque Data Chart .................................................................................................................................................................. 4
Installation Note ....................................................................................................................................................................... 5
Step 1: Set the hooklift onto the truck frame. .......................................................................................................................... 5
Step 2: Bolt Tie-Down Angles to Mounting Plates. ................................................................................................................... 6
Step 3: Weld Tie-Down Angle to Mounting Plates................................................................................................................... 7
Step 4: Drill Mounting Holes into Frame Rail. ............................................................................................................................ 8
Step 5: Bolt Tie-Down Angles to Truck Frame. .......................................................................................................................... 8
Mounting Kit Overview - PN 58597 ............................................................................................................................................ 9
Step 6: Install bumper. .............................................................................................................................................................. 10
Step 7: Install tarper tower (If applicable). ............................................................................................................................ 10
Step 8: Install hydraulic reservoir and valve bank. ................................................................................................................ 10
Reservoir Assembly (2 Section Cable Controls) - PN 86464 .............................................................................................. 11
Reservoir Assembly (3 Section Cable Controls) - PN 86474 .............................................................................................. 12
Reservoir Assembly (2 Section Air Controls) - PN 86468 .................................................................................................... 13
Reservoir Assembly (3 Section Air Controls) - PN 86478 .................................................................................................... 14
Reservoir Subassembly - PN 86006 ....................................................................................................................................... 15
Step 9: Install PTO and pump. ................................................................................................................................................. 18
Step 10: Route hydraulic hoses. .............................................................................................................................................. 19
Hose Kit - PN 38955 (Fixed Hook Height Models) ............................................................................................................... 19
Hose Kit - PN 84958 (Adjustable Hook Height Models) ...................................................................................................... 20
Power Beyond VDM8 Valve ................................................................................................................................................. 21
Step 11: Route Electrical Components .................................................................................................................................. 22
Step 12: Install cab and PTO controls. .................................................................................................................................... 23
Cable Controls ...................................................................................................................................................................... 23
Air Controls ............................................................................................................................................................................. 24
Step 13: Install Hoist Up Light Sensor - PN 83115 .................................................................................................................... 25
Step 14: Install mud flaps and fenders.................................................................................................................................... 26
Poly Tandem Fender Assembly - PN 58217 ......................................................................................................................... 26
Steel Tandem Fender Assembly - PN 100617 ..................................................................................................................... 27
Step 15A: Apply Hooklift Assembly Decals ............................................................................................................................ 28
Step 15B: Apply Chassis Decals ............................................................................................................................................... 29
Step 16: Fill reservoir and activate hydraulic flow. ................................................................................................................ 30
Step 17: Operate hooklift. ........................................................................................................................................................ 30
Set System Relief Pressure ..................................................................................................................................................... 31
Chapter 3 - Assembly Drawings ...................................................................................................................................................33
Base Assembly - PN 34135 ........................................................................................................................................................ 33
Dump Assembly - PN 34137 ..................................................................................................................................................... 34
Secondary Assembly - PN 34139 ............................................................................................................................................. 35
Main Cylinder Assembly - PN 39043 ........................................................................................................................................ 36
Jib Assembly (54” Hook Height) - PN 56157 ........................................................................................................................... 37
Jib Assembly (61.75” Hook Height) - PN 40121 ...................................................................................................................... 38
Jib Assembly (54/61.75” Hook Height) - PN 47348 ................................................................................................................ 39
Hose Track - PN 59003 ............................................................................................................................................................... 40
Slider65 Cylinder Assemblies .................................................................................................................................................... 41
Valve Bank Parts Drawing ........................................................................................................................................................ 42
Pintle Bumper - PN 63580 ......................................................................................................................................................... 43
Toolbox Assembly - PN 8480 ..................................................................................................................................................... 44
Toolbox Assembly - PN 10401 ................................................................................................................................................... 44
Toolbox Assembly - PN 10402 ................................................................................................................................................... 44