manualshive.com logo in svg

STEINWAY LYNGDORF Steinway & Sons Model C, Installation Manual

Share
Download
STEINWAY LYNGDORF Steinway & Sons Model C Installation Manual Download Page 12

Steinway & Sons Model C – Installation Manual, version 2.1 

12 

SERVICE INFORMATION 

To obtain warranty service, you must contact your original dealer or the Steinway Lyngdorf distributor of the 
region or country where you are located. If you have trouble locating an authorized representative, please find 
contact information at 

www.steinwaylyngdorf.com

,  

 

Steinway Lyngdorf  
Ulvevej 28 
DK 7800 Skive 
Denmark 

 
In some cases, it may be necessary to return the equipment to Steinway Lyngdorf or an authorized service 
provider for repair; therefore, it is recommended that you save your original packing materials. Steinway 
Lyngdorf will not be responsible for any damage due to unauthorized packing or shipment in non-original 
packing materials. If return is made in authorized packaging, risks are borne by Steinway Lyngdorf. Additional 
charges may occur if new packing materials are required for return shipment. 
 
 

 

Summary of Contents for Steinway & Sons Model C














Reviews:

No comments

Brands by name

Popular brands

Load more brands