- 10 -
- 11 -
L
Disconnect the power supply
before attempting any work
on the sensor!
L
Before installation, make sure
that power has been switched
off at the breaker and check
that the circuit is dead with
a voltage tester.
L
Installing the sensor involves
work on the line voltage power
supply. This work must
therefore be carried out
professionally in accordance
with the applicable Nation
Electrical Codes and electrical
operating conditions.
L
Control output DIM-24
(0-10 V) must only be used
for connecting electronic
ballasts with an electrically
isolated 10V dimming
control input.
System Components
a
Ceiling mount adapter
b
Sensor
c
Sensor settings cover plate
d
Sensor DIP switch settings
(1) Normal / Test mode
(2) Manual 'ON' / Automatic
'ON' mode
(3) Momentary / Maintained
switch option
(4) 'ON' only / 'ON'&'OFF'
manual switching
(5) Constant light level DIM
control option
(6)(7)(8)
Trigger mode
(DT CM sensor only)
e
Light level setting
f
Occupancy time
delay setting
Switching output 1
g
HVAC stay-'ON' time
Switching output 2
h
HVAC switch-'ON' delay
Switching output 2
i
Reach setting
(ultrasonic only)
10
.1
COM1-24 Wiring
10
.2
COM2-24 Wiring
10
.3
COM2-24 Multiple Sensor
Wiring
10
.4
DIM-24 Wiring
10
.5
DIM-24 Multiple Sensor
Wiring
k
Mounting plate
l
Installation /
Dimensional Drawings /
Positioning / Coverage
Pattern / Recommended
Application
m
Stay 'ON' time DIM before
'OFF' option
n
Trigger mode options
o
Anchor bolts
p
1/2" Snap in chase, washer,
lock nut
Installation
(see page 3)
For indoor use only.
Mounts to a round 3.0 mud-ring
or can be mounted directly to
the ceiling or wall using anchor
bolts. Additionally, the sensor
can be mounted to the ceiling
using the supplied 1/2" snap in
chase nipple, washer and lock
nut.
When mounting to the ceiling,
the ceiling mount adapter should
be used.
Accessories:
- RC 8 Service Remote
- RC 4 User Remote
- Smart Remote
Operating Instructions
Installer:
This product has been
manufactured and 100% quality
tested.
Please read all of the instructions
before installation. This will help
you to be familiarized with all the
features and options available to
you with these devices.
This will also assist you to
minimize installation time and
provide maximum energy savings
and trouble-free operation.
Safety Warnings
l
How it Works / Basic Function
The Control Pro IR CM and DT CM
presence detector product family
is intended to control lighting and
HVAC in commercial buildings,
schools, public building, etc.
Lighting is controlled in relation to
both the presence of motion and
ambient light levels. The HVAC
output on the (COM2-24) is
signaled in relation to only the
presence of motion.
Commissioning adjustments are
made by potentiometer or dip
switch settings on the sensor or by
the optional (RC8 service remote)
commissioning tool.
IR CM COM1-24
DT CM COM1-24
1 switching output (COM1-24 Low
Voltage) operating in relation to
the detection of motion and
ambient light level.
Settings:
- Light level setting
- Occupancy time delay,
Pulse mode, IQ mode
- Ultrasonic reach setting
(DT CM only)
- Normal / Test mode
- Manual 'ON' /
Automatic 'ON' mode
- Momentary /
Maintained switch option
- 'ON' only /
'ON'&'OFF' manual switching
- Trigger mode (DT CM only)
IR CM COM2-24
DT CM COM2-24
1 low voltage switching output
operating in relation to the
detection of motion and ambient
light level. An additional isolated
normally open and normally
closed set of dry contact closures
for signaling HVAC (heating/
ventilation/air conditioning) in
relation only to the presence of
persons.
Settings:
- Light level setting
- Occupancy time delay,
Pulse mode, IQ mode
- HVAC stay-'ON' time
- HVCA switch-'ON' delay,
Auto-HVAC mode
- Ultrasonic reach setting
(DT CM only)
- Normal / Test mode
- Manual 'ON' /
Automatic 'ON' mode
- Momentary /
Maintained switch option
- 'ON' only /
'ON'&'OFF' manual switching
- Trigger mode (DT CM only)
IR CM DIM-24
DT CM DIM-24
1 low voltage switching output
operating in relation to the
detection of motion and ambient
light level. An additional isolated
0-10 volt dimming output
operating in relation to the
amount of daylight present.
Settings:
- Light level setting
- Occupancy time delay, IQ mode
- Stay 'ON' time DIM before 'OFF'
- Constant light level DIM
control option
- Ultrasonic reach setting
(DT CM only)
- Normal / Test mode
- Manual 'ON' /
Automatic 'ON' mode
- Momentary /
Maintained switch option
- 'ON' only /
'ON'&'OFF' manual switching
- Trigger mode (DT CM only)
US
