Steerix FUSION Instruction Manual Download Page 1

TAKE CONTROL

Model No: 18009

2.4GHz RTR STEERIX FUSION RC CATAMARAN SAILBOAT

ITEMS REQUIRED FOR OPERATION

Ahoy there Skipper! You’ve just made your first steps into the exciting world of RC sailing. Please 
take a few minutes to read this manual to find out how to assemble your boat, gain an 
understanding of nautical terminology and learn the basics of sailing techniques.

Please take the time to read and understand these instructions completely before attempting to sail 
for your first time. This manual includes everything you need to know about assembly, operations 
and maintenance. A small amount of time reading this manual will save you big headaches in the 
future. Please also note that this model is not a toy. Assembly and operation of this catamaran 
requires adult supervision.

TAKE CONTROL

TAKE CONTROL

Fusion Catamaran Hull

(Servos, Receiver &

Battery Box Pre-Installed)

Sails, Mast & Boom Set

Two PVC Hatch Covers

Boat Stand

2.4GHz 2CH Transmitter

(The control sticks are included

in the battery compartment)

27

TAKE CONTROL

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications to this product not expressly approved by the party responsible
for compliance may void the user’s authority to operate the equipment.

Summary of Contents for FUSION













Reviews: