Cue lever
TURNTABLE OPERATION
Preparing to use the Turntable
1.
Open the Dust Cover, and untwist and remove the black tie-wrap securing the Tone Arm.
2.
Make sure all packing materials, tape, wire, etc. have been removed.
3.
Make sure the white needle guard has been removed from the red stylus holder before playing a
record.
1.
Slide the Tone Arm hold-down securing clip to the right to release the tone arm.
2.
Re-lock the hold-down clip when moving the unit to another location.
ACCESSORY SUPPLIED
45rpm Spindle Adaptor: To play a 45rpm record with the centre clip missing, remove the
round adaptor from the record player deck, place thumb & forefinger in the recesses, pull it upwards, then place
it on the Turntable Spindle. The record can then be placed on the turntable
.
1
Press the "POWER" key to Switch the unit
ON
with the ON/OFF switch.
Turn the
VOLUME
control to mid-range position.
2
Set the function Switch (CD / USB SD / AUX-PH / TUNER / TAPE) to
AUX-PH
to select the
TURNTABLE
function.
3
Set the
SPEED CONTROL
Switch to the correct speed (33, 45 or 78 rpm) required for the selected record.
4
Place a record on the platter, use the supplied 45rpm spindle adaptor if required.
5
Use the
CUE LEVER
to raise the tone arm off its rest.
6
Move the Tone Arm towards the record and
the turntable will start rotating.
7
Use the CUE LEVER to lower the Tone Arm onto the point where you
want the record to start playing.
Note:
If the Cue Lever stick is not raised, it is possible to lower the
tone arm manually. When the record has finished playing, it will
stop automatically – the tone arm can then be lifted up with the Cue
Lever and returned to the arm rest. Lower it and secure it with the
clip after you have finished playing your records.
8
Adjust the Volume.
9
Playing records with the dust cover down will protect the record and turntable from dust.
( 7 )
CD PLAYER OPERATION
Listening to an Audio CD or MP3 CD
1
Press the "POWER" button to ON
5
Press the CD door down gently to close it and to
switch the device on.
connect the drive – the CD Player will read & scan
the contents of the disc.
(a) Audio CD -
Total number of Tracks:
The total number of tracks will show on the
display.
2
Set the function switch to
CD
mode
(CD / USB SD / AUX-PH / TUNER / TAPE)
(b)
MP3-CD
- Total number of tracks:
The total number of tracks is displayed on the screen.
3
Gently press ‘
OPEN’
on the centre of the
6
Playback will start automatically.
Turntable Platter to open the CD
Compartment, the cover will lift up .
Caution:
In some cases, a CD Instruction
Card may be found in the tray. If this is the
Case, after reading it, this must be removed
before playing a CD!
4
Place a pre-recorded Audio disc into
7
Turn the volume knob to adjust the volume.
the tray with the printed side facing up.
Make sure the disc is locked securely
onto the Tray
*
.
Important Notes:
-
Never place more than one disc in the tray.
-
*
The CD must be placed in the middle of the CD drive.
-
If the CD is not inserted correctly, it could cause the tray to open with difficulty or it could even prove impossible
to re-open it as soon as it is closed. To avoid this problem, you need to be sure that you have inserted the CD
correctly.
-
The drive opens automatically after you press on
OPEN
in the centre of the Turntable Platter.
-
Do not open or force it to open by hand – this may cause irreparable damage to the mechanism and this would
not be covered by the warranty.
( 8 )
CUE LEVER
