SteelMax Rail Runner LT Operator'S Manual Download | Manualshive

Page: 36 / 53

background image

Rail Runner LT

Rail Runner LT

– Operator’s Manual

36

5.14. Torch clamps

5.14.1. 16

–22 mm torch clamp

Allows using a torch with the diameter of 16

–22 mm (0.63–0.87″).

5.14.2. 16

–22 mm torch clip

The clip allows using a torch with the diameter of 16

–22 mm (0.63–0.87″). Use the

4 mm hex wrench to tighten the torch in the clip.

5.14.3. 22

–35 mm torch clamp

Allows using a torch with the diameter of 22

–35 mm (0.87–1.38″).

Part number:
ZRZ-0466-19-00-00-0

Part number:
ZRZ-0466-04-01-00-0

Part number:
ZCS-0476-06-01-00-0

«
...
34
35
36
37
38
...
»

Summary of Contents for Rail Runner LT






















































Reviews:

No comments

Related manuals for Rail Runner LT

Brand: idiag Pages: 12

Brand: YYZ Lighting Pages: 3

Brand: Camp Safety Pages: 118

Brand: Ultrafast Systems Pages: 39

Brand: Mackworth Pages: 2

ActiveFinder One

Brand: LaserLiner Pages: 92

Brand: Ultrawave Pages: 30

Brand: Ultrasound Technologies Pages: 12

Brand: Ultimate Healthcare Pages: 2

Brand: Ultimate Healthcare Pages: 40

Brand: Zero 88 Pages: 12

Brand: Zeiss Pages: 119

Brand: Zehnder Rittling Pages: 32

Brand: popular Pages: 27

Avisa Line XL04

Brand: FHF Pages: 2

Brand: Joerns Healthcare Pages: 106

Brand: Tripp Lite Pages: 24

Brand: TDX Tech Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands