![background image](http://html1.mh-extra.com/html/steele-products/sp-pb140/sp-pb140_owners-manual_1369953016.webp)
Fitting the light bulb
into the light housing.
ti
w
e
r
c
s
d
n
a
b
l
u
b
t
h
g
il
e
h
t
e
k
a
T
.
1
flexible tube allowing it to be positioned where it
a
n
o
d
e
t
a
c
o
l
s
i
t
h
g
il
e
h
T
.
2
will project the most light onto the work area.
Turning the laser on and off
“I” position.
e
h
t
o
t
h
c
ti
w
s
f
f
o
/
n
o
t
h
g
il
r
e
s
a
l
e
h
t
s
s
e
r
p
n
o
r
e
s
a
l
e
h
t
n
r
u
t
o
T
.
1
e laser light on/off switch to the “O” position.
h
t
s
s
e
r
p
f
f
o
r
e
s
a
l
e
h
t
n
r
u
t
o
T
.
2
the laser adjustment knob in an anti-clockwise
n
r
u
t
e
n
il
r
e
s
a
l
e
h
t
t
s
u
j
d
a
o
T
.
3
direction to loosen it and then move it to the left or right until the laser line
is in line with the blade. Turn the laser adjustment knob in a clockwise
direction to tighten it.
Installing and removing band saw blades
WARNING.
Always ensure that the saw is switched off and unplugged from
the power supply before making any adjustments.
This bandsaw is supplied with a general purpose woodcutting blade.
m the table.
o
rf
e
c
n
e
f
p
ir
e
h
t
e
v
o
m
e
R
.
1
m under the work table by loosening the two knobs.
o
rf
t
e
k
c
a
r
b
e
h
t
e
v
o
m
e
R
.
2
3. Open both housing doors.
n knob to slacken the blade.
o
i
s
n
e
t
e
d
a
l
b
e
h
t
n
e
s
o
o
L
.
4
g it through the slot in the work table, the upper
n
i
d
i
u
g
y
b
e
d
a
l
b
e
h
t
e
v
o
m
e
R
.
5
blade guide and the blade cover on the saw housing.
g that the teeth are pointing towards the front
n
ir
u
s
n
e
e
d
a
l
b
w
a
s
w
e
n
e
h
t
ti
F
.
6
of the saw where the doors are.
knob.
n
o
i
s
n
e
t
e
d
a
l
b
e
h
t
g
n
it
a
t
o
r
y
b
e
d
a
l
b
w
e
n
e
h
t
n
o
i
s
n
e
t
y
lt
h
g
i
L
.
7
saw wheels.
d
n
a
b
e
h
t
f
o
s
e
r
y
t
r
e
b
b
u
r
e
h
t
n
o
e
d
a
l
b
w
a
s
d
n
a
b
e
h
t
e
rt
n
e
C
.
8
in the centre
g
n
i
n
n
u
r
s
i
e
d
a
l
b
e
h
t
e
r
u
s
n
e
o
t
d
n
a
h
y
b
l
e
e
h
w
r
e
p
p
u
e
h
t
n
r
u
T
.
9
of the rubber-lined wheels.
blade tracking.
w
a
s
e
h
t
t
s
u
j
d
a
,
d
e
ri
u
q
e
r
fI
.
0
1
tighten the blade tension knob.
,t
c
e
r
r
o
c
s
i
g
n
i
k
c
a
rt
e
h
t
e
c
n
O
.
1
1
Adjust the thrust bearing and guide pins as described earlier.
12. Close both housing doors.
e back into position.
d
i
u
g
e
d
a
l
b
r
e
w
o
l
e
h
t
g
n
i
w
S
.
3
1
o
w
t
e
h
t
g
n
i
s
u
e
l
b
a
t
k
r
o
w
e
h
t
r
e
d
n
u
e
p
a
h
s
U
e
h
t
h
c
a
tt
A
.
4
1
screws and two thumb nuts.
g
n
i
h
s
u
p
y
b
t
i
e
r
u
c
e
s
d
n
a
e
l
b
a
t
e
h
t
o
t
e
c
n
e
f
p
ir
e
h
t
h
c
a
tt
A
.
5
1
down the rip fence locking handle.
16