manualshive.com logo in svg

Steelcase Think 465, Manual

Share
Download
Steelcase Think 465 Manual Download Page 17

2

3

5

Page 17 of 19

939546506 Rev E

Removal & Installation
of the Mechanism

1. 

See page 11 for removal of seat, page 10 for removal 

of back frame and page 12 for removal of arms.

2. 

Snap cable attachment clip out of the swing cam 

bracket by pushing outward on cable attachment clip.

3.

 Remove cable from attachment post.

4. 

Pry other end of cable up from attachment bracket 

with a flat bladed screwdriver (4a) and remove cable 
from pneumatic cylinder adjustment bracket (4b).

5.

 Remove black slides from mechanism.

6. 

See page 19 for removal of cylinder from chair 

control mechanism.

Reverse to install.

SWING CAM

BRACKET

CABLE

ATTACHMENT CLIP

ATTACHMENT POST

CABLE

4a

4b

PNEUMATIC CYLINDER

ADJUSTMENT BRACKET

ATTACHMENT

BRACKET

PNEUMATIC

CYLINDER

ADJUSTMENT

BRACKET

Top View of Cylinder

On installation, align cylinder with 
center of chair control as shown
before seating on cylinder.

CABLE

ATTACHMENT

BRACKET

CABLE

Summary of Contents for Think 465




















Reviews:

No comments

Brands by name

Popular brands

Load more brands