Steelcase c:scape Low Storage Series Assembly Instructions Manual Download Page 14

Page: 14 / 15

NOSE OF
TETHER

SIDE VIEW

TOP VIEW

1/2" GAP

PUSH

BEAM

IMPORTANT!

Page 14 of 15

939500368 Rev K

Tether the case to the beam.

a) Push the case so that the nose of the

storage to beam tether slides between

the underside of the beam and top

side of beam cover.

b) It may be necessary to slide the

case left or right to engage the actuator

portion of the storage to beam tether.

IMPORTANT STEP:

Pull the storage

unit on the left side, then the right side

to confirm that the storage unit is

secured to the beam.

CAUTION:

Failure to secure the

case to the beam could result in an
unstable condition where the case
could tip causing personal injury.

Summary of Contents for c:scape Low Storage Series
















Search results

Summary of Contents for c:scape Low Storage Series

Reviews:

Related manuals for c:scape Low Storage Series

Brands by name

Popular brands

Steelcase c:scape Low Storage Series, Assembly Instructions Manual

Search results

Summary of Contents for c:scape Low Storage Series

Reviews:

Related manuals for c:scape Low Storage Series

Brands by name

Popular brands