background image

12

718.573 | 11.27

5.3. Deep Discharging Protection

The regulator protects the connected battery against an excessive discharging. If the bat-

tery falls below a specified charge level (during SOC control) or battery voltage (during 

the voltage-controlled function), the load output is disconnected and the discharge of 

the battery is prevented. The display shows the early warning and disconnection during 

deep discharging. The setpoints of the deep discharging protection are predefined and 

cannot be reset. 

6.  Regulator Settings

The battery type, control type and night light function can be set in the regulator. Points 

for the auto-test and the serial number query are also located within the menu. The set-

tings remain when the battery is disconnected. 

6.1. Calling up and Modifying the Settings

Press the left button for at least 3 seconds to open the first setting window (control 

type). Press the left button again to call up the various windows.
Press the right button to modify settings. The display begins to flash. Now, with the left 

button select the settings options. The setting must be saved with the right button. The 

display then stops flashing.
The normal window reappears after a 30 second waiting period or pressing the left but-

ton for 3 seconds. This applies to all windows.

6.2. SOC Setting / Voltage Control

The SOC control is the factory setting. This way, the charging procedure and the deep 

discharging protection are controlled by the calculated SOC value for ideal battery 

usage. If external loads are connected directly to the battery you can change to voltage 

control. The bar 

gauge can then be 

enabled or disabled. 

See chapter 10 for 

voltage  thresholds.

6.3. Gel / Liquid Battery Type Setting 

The standard setting is “Li”. The setting 

of the battery type influences the cutoff 

voltage of the controller. If you use a Gel 

or AGM battery, you have to change the 

battery type to GEL.

Caution! An incorrect battery type setting can damage the battery!

Summary of Contents for PR 2020 IP65

























Reviews: