Separate collection for electrical and electronic equipment.
CAN ICES-3(B) / NMB-3(B)
Model P16V1
PLUG.
BEFORE YOUR FIRST USE
• Insert a microSD or microSDHC memory card
(not supplied*), with a capacity of between 1
and 32GB.
• Insert the battery, model for GoPro® HERO3
** (not included *), when charged.
• For horizon correction, calibrate the gyros of
your SteadXP@ by leaving it lit up on a stable
surface over the recommended operating
temperature range.
CONNECTION
• Insert into the flash shoe of your
device and secure it with the tightening wheel in
alignment with the lens.
• Turn it on by plugging the audio cable (not
included*) into the stereo microphone jack
of your device.
Option:
You can genlock the
by using its RCA input (bi- or tri-level
signal) with compatible cameras.
• At first, the indicator light (LED) of the
will alternate between red and
orange (1). After a few seconds, it will flash (2),
varying from green to red according to battery
level.
You’re ready to shoot!
SHOOT.
SETTINGS
• Ensure that you disable the EIS/OIS on your
device and/or your lenses.
• Use a fixed focal length. Zooming is not
recommended.
• Set your shooting settings.
Tip:
The greater
the focal length, the more dynamic the footage
will be, and the more the shutter speed should
be increased (between 1/150 and 1/1000s).
SHOOTING
• Plug in and switch the camera on.
Warning:
The LED light on the will
flash for the duration of shooting (2).
• At the beginning of shooting it is advisable to
make a sudden movement of low amplitude,
aiming at a background with more than 5m and
without a foreground.
• It is advisable to disconnect and then
reconnect the audio cable between each shot,
in order to create a new data file.
Let your imagination run wild!
ENJOY!
SOFTWARE SYSTEM REQUIREMENTS
• Windows 7, 8.1, 10
• Mac 10.11 (El Capitan), 10.12 (Sierra)
• 64-bit operating system
• 2GB of RAM available
USING THE SOFTWARE FOR THE FIRST TIME
After starting up the software, enter the contact
email address linked to your order, as well as
the serial number found on your
certification label (SN:
XXXXXXXX
).
TRANSFERRING VIDEO DATA
Use the «Browse» function, or let the software
automatically detect video data from your
device via its storage unit.
DATA TRANSFER
• Use a USB cable (not included*) to connect
with your computer, then turn
it on. The software automatically detects
the movement data of your and
synchronizes it with the video data from your
device.
• You can also import data using the memory card.
STEPS FOR STABILIZATION
•
Input
Select your camera profile. For best
results, calibrate your optics following the
SteadXP Calibration instructions. Each lens has
to be calibrated separately in the appropriate
recording mode.
•
Sync
Semi-automated adjustment of the
frame-by-frame data. Once you have reviewed
it, click on «Play» and then on «Validate».
•
Preview
Split your clips, modify your
stabilization settings, then click on «Optimize».
•
Advanced
Select your export options, then
click on «Rendering».
Find more information on SteadXP software,
as well as video tutorials, at
steadxp.com/
manual
.
PRECAUTIONS FOR USE
* WE RECOMMEND USING
• A 2GB FAT16 microSD card of type 9191AA
2G 07SM1 from Transcend Information Inc.**.
• A rechargeable GoPro®** Li-ion 3.7V
1180mAh 4.37Wh Polymer Battery Pack of type
AHDBT-302 with a USB 2.0 A to Micro B 975111
cable from Conrad SAS**.
• A 7cm, 3.5mm male-to-male L8-BK TRS audio
cable from FiiO Electronics Technology Co., Ltd.**.
Check manufacturer’s directions for use.
After each use, turn off your camera and
disconnect .
Operating temperatures: 0/+50°C (+32/122 F).
Storage temperature: -10/+60°C (+14/140 F).
Humidity: 80% max. Altitude: 2000m max.
is not waterproof.
Charge your battery only via a USB 2.0 port.
All equipment connected to your SteadXP
must be SELV (Safety Extra Low Voltage) and
Limited Power Sources, as defined by chapters
2.2 and 2.5 of standards EN 60950-1 :2006 +
A11 :2009 + A1 :2010 + A12 :2011 + A2 :2013.
Always use the recommended battery type. Use
of a battery of wrong type may cause explosion
Never use a damaged or flat battery.
Make sure to remove the battery from your
after each use, especially when
traveling by air.
I
MPORTANT NOTE: FCC Caution Statement
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
Caution:
the user that changes or modifications not
expressly approved by the party responsible
for compliance could void the user’s authority
to operate the equipment.
NOTE:
This
equipment has been tested and found to comply
with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or television
reception which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
For full warranty terms, see
steadxp.com/
warranties
.
** GoPro, HERO, BacPac are trademarks of GoPro,
Inc. SteadXP SAS is not affiliated with GoPro, Inc.
Other names and trademarks are the property of their
respective owners.
QUICK START GUIDE
See the complete user manual at
steadxp.com/manual
Need some help?
Made in FRANCE
SteadXP SAS - 8a chemin de la Cour 38660 St Hilaire du Touvet
Contact: (+33) 4 28 70 00 38
FCC ID: 2ALGS-P16V1