ENGLISH
12
13
14
15
16
17
Tool holder
18
Chisel position selector
Handle
Carrying handle
Knurled nut for carrying handle
Limit bolt
Tool shank
3.- Assembly
f
Before any work on the machine itself, pull
the mains plug.
3.1.- Auxiliary Handle
f
Operate your machine only with the auxiliary
handle
11.
Rotating the Auxiliary Handle
The auxiliary handle
11
can be set to any position
for a secure and low-fatigue working posture.
Turn the bottom part of the auxiliary handle
11
in
counterclockwise direction and swivel the auxiliary
handle
11
to the desired position. Then retighten
the bottom part of the auxiliary handle
11
by turning
in clockwise direction.
Pay attention that the clamping band of the
auxilia-
ry
oned in the groove on the housing
handle is positi
as intended for.
3.2.- Changing the Tool
The dust protection cap
3
largely prevents the
entry of drilling dust into the tool holder during
operation. When inserting the tool, take care that
the dust protection cap
3
is not damaged.
f
A damaged dust protection cap should be
changed immediately. We recommend hav-
ing this carried out by an after-sales service.
Inserting SDS-plus Drilling Tools
The SDS drill chuck allows for simple and con-
venient changing of drilling tools without the use
of additional tools.
Clean and lightly grease the shank end of the tool.
Insert the tool in a twisting manner into the tool
holder until it latches itself.
Check the latching by pulling the tool.
As a requirement of the system, the SDS drilling
tool can move freely. This causes a certain radial
run-out at no-load, which has no effect on the
accuracy of the drill hole, as the drill bit centres
itself upon drilling.
Removing SDS Drilling Tools
Push back the locking sleeve
4
and remove the
tool.
3.3.- Carrying Handle (HD15K / HD17K)
The carrying handle
13
can be turned to any posi-
tion. Loosen the knurled nut
14
, turn the carrying
handle
13
around the machine axis to the desired
position and tighten the knurled nut
14
again.
The carrying handle
13
can also be mounted facing
to the other side. Completely unscrew the knurled
nut
14
and then pull out the hexagon bolt upward.
Pull off the carrying handle
13
to the side and tilt
the remaining clamping element by 180°. Mount
the carrying handle
13
in reverse order.
3.4.- Changing the Tool (HD15K / HD17K/
f
Before any work on th e machine itself,
pull the mains plug.
Clean the tool shank
16
and apply a light coat of
grease.
Pull out the lock bolt
15
and turn it 180° in anticlock-
wise direction. Allow the lock bolt
15
to latch again.
MH2K / MH6K / MH8K)
22
22
Insert the tool into the tool holder to the stop.
The groove of the tool shank
16
must face upward
as shown in the figure.
Check the latching by pulling the tool.
HD21K, HD27K / HD27BK, HD28K, HD5K,
HD5BK, HD50K, HD55K, HD3K, HD6K, HD6BK,
HD45K, MH2K, MH6K, MH8K
Summary of Contents for HD21K
