background image

1

Instruction Manual

PRINTED 1112 

325366-000

Keep thIs Manual In the pocKet on heater for future reference 

whenever MaIntenance adjustMent or servIce Is requIred.

 ultra low noX coMMercIal Gas water heaters

• 

for Your safety

 •

AN ODORANT IS ADDED TO THE GAS USED 

BY THIS WATER HEATER.

Models sBl 100 76ne

series 100

InstallatIon - operatIon - servIce  

- MaIntenance - lIMIted warrantY

PlAcE THESE INSTRUcTIONS ADjAcENT TO HEATER AND NOTIfY OWNER TO kEEP fOR fUTURE REfERENcE.

Read and understand this instruction

manual and the safety messages

herein before installing, operating or

servicing this water heater.
Failure to follow these instructions and

safety messages could result in death

or serious injury.
This manual must remain with the

water heater.

Low Lead Content

WARNING:  If   the information   in   these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury or death.

Do  not store  or  use  gasoline  or other

flammable   vapors  and  liquids   in  the

vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.
Do not  touch any electrical switch;  do

not use any phone in your building.
Immediately   call   your   gas   supplier

from a  neighbor’s  phone.  Follow the

gas supplier’s instructions.
If you cannot  reach your  gas supplier,

call the fire department.

Installation  and  service  must  be

performed  by  a  qualified  installer,

service agency or the gas supplier.

500 Tennessee Waltz Parkway

Ashland city, TN 37015

Summary of Contents for SBL 100 76N





































Reviews: