background image

3

SAFE INSTALLATION, USE AND SERVICE

The proper installation, use and servicing of this water heater is extremely important to your safety and the safety of others.
Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and 
others of a potential injury hazard.  Read and obey all safety messages and instructions throughout this manual.  It is very important 
that the meaning of each safety message is understood by you and others who install, use, or service this water heater.

All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the safety message, and 
how to avoid the risk of injury.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances 
known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of 
potential exposure to such substances.
This product contains a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm. This 
appliance can cause low level exposure to some of the substances listed in the Act.

DANGER

WARNING

CAUTION

CAUTION

DANGER indicates an imminently
hazardous situation which, if not avoided,
will result in injury or death.

This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.

WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in injury or death.

CAUTION indicates a potentially hazardous
situation which, if not avoided, could result in
minor or moderate injury.

CAUTION used without the safety alert
symbol indicates a potentially hazardous
situation which, if not avoided, could result in
property damage.

ASME CRN

ANSI / NSF 5

APPROVALS

Summary of Contents for SBD85500NE





















































Reviews: