background image

55

THIS WARRANTY IS APPLICABLE TO THE ORIGINAL OWNER 

ONLY. 

If  the  glass  lined  tank  in  this  water  heater  shall  prove  upon 

examination by (the warrantor) to have leaked during the warranty period 

in normal residential use, due to natural corrosion from potable water 

therein, the warrantor will furnish the ORIGINAL OWNER a replacement 

water heater of equivalent size and current model, or a replacement part 

for any component part which fails in normal use, in accordance with the 

warranty terms and conditions specified below. 

THE WATER HEATER 

REPLACEMENT MODEL OR PART WILL BE WARRANTED FOR 

ONLY THE UNEXPIRED PORTION OF THE ORIGINAL WARRANTY. 

The  warranty  period  will  be  determined  by  the  original  installation 

date of the water heater. 

PROOF-OF-PURCHASE AND PROOF-OF-

INSTALLATION ARE NECESSARY TO 

VALIDATE THIS WARRANTY. 

This warranty is not transferable.

warrantY perIod

product line

tanK

1

parts

2

GP 6 50YTPDT

6 YEARS

6 YEARS

GP 6 50HTPDT

6 YEARS

6 YEARS

When the water heater has been used for other than 

single

  family 

residential application: 1.  The Tank warranty shall be reduced to 3 

years on 10 year models and 1 year on 6 and 8 year models.  2. The 

parts warranty shall be reduced to 1 year for all models.  Returned 

parts which meet any of the following conditions are not covered by 

this warranty: 1) improper installation or removal; 2) damaged by other 

than normal wear; 3) replaced for cosmetic purposes; or 4) returned 

with defaced date codes.

condItIons and eXceptIons

This warranty shall apply only when the water heater is installed and 

operated in accordance with: 1) all local fire codes and plumbing codes, 

ordinances and regulations; 2) the printed instructions provided with it; 

3) good industry practices; and 4) proper safety practices such as but 

not limited to a properly sized drain pan if installed in an area where 

leakage from connections of the tank would result in damage to the area 

adjacent to the heater.  In addition, a new temperature and pressure 

relief valve, certified by the Canadian Standards Association must have 

been properly installed and piped to the nearest drain.
This warranty shall apply only when the heater is:
•  owned by the original purchaser; 

•  used  at  temperatures  not  exceeding  the  maximum  calibrated   

setting of its thermostat;

•  not subjected to excessive water pressure fluctuations and not 

subject to an operating pressure greater than 150 P.S.I.;

•  filled with potable water, free to circulate at all times and with the 

tank free of damaging water sediment or scale deposits;

•  used in a non-corrosive and non-contaminated atmosphere;

•  used with factory approved anode(s) installed;

•  in its original installation location;

•  in the United States and its territories or possessions or Canada;

•  sized in accordance with proper sizing techniques for residential 

water heaters;

•  bearing  a  rating  plate  which  has  not  been  altered,  defaced  or 

removed except as required by the warrantor;

•  used  in  an  open  system  or  in  a  closed  system  with  a  properly  

sized and installed thermal expansion tank;

•  fired at the factory rated input using the fuel stated in the face of 

the rating plate;

•  operated with inner and outer combustion chamber doors in place;

•  maintained  in  accordance  with  the  instructions  printed  in  the   

manual included with the heater.

Any accident to the water heater or any part thereof (including freezing, 

fire, floods, or lightning), any misuse, abuse or alteration of it, any 

operation of it in a modified form, or any attempt to repair tank leaks 

or parts, will void this warranty.

servIce and labor responsIbIlItY

UNDER THIS LIMITED WARRANTY, THE WARRANTOR WILL 

PROVIDE  ONLY  A  REPLACEMENT  WATER  HEATER  OR  PART 

THEREOF.  THE OWNER IS RESPONSIBLE FOR ALL OTHER COSTS.  

Such costs may include but are not limited to:
a.  Labor charges for service, removal, or reinstallation of the water 

heater or part thereof.

lIMIted resIdentIal Gas warrantY

b.  Shipping and delivery charges for forwarding the new water heater 

or replacement part from the nearest distributor and returning the 

claimed defective heater or part to such distributor except in the 

state  of  California  where  such  charges  are  the  manufacturer’s 

responsibility.

c.  All cost necessary or incidental for handling and administrative 

charges,  and  for  any  materials  and/or  permits  required  for 

installation of the replacement heater or part.

lIMItatIon on IMplIed warrantIes

Implied warranties, including any warranty of merchantability imposed 

on  the  sale  of  this  heater  under  state  law  are  limited  to  one  year 

duration for the heater or any of its parts.  Some states do not allow 

limitations  on  how  long  an  implied  warranty  lasts,  so  the  above 

limitations may not apply to you.

claIM procedure

Any claim under this warranty should be initiated with the dealer 

who  sold  the  heater,  or  with  any  other  dealer  handling  the 

warrantor’s products.
The  warrantor  will  only  honor  replacement  with  identical  or  similar 

water heater or parts thereof which are manufactured or distributed 

by the warrantor.
Dealer  replacements  are  made  subject  to  in-warranty  validation 

 

by warrantor.

PROOF-OF-PURCHASE AND PROOF-OF-INSTALLATION DATES 

ARE REqUIRED TO SUPPORT WARRANTY FOR CLAIM FROM 

ORIGINAL OWNER. THIS FORM DOES NOT CONSTITUTE PROOF-

OF-PURCHASE OR PROOF-OF-INSTALLATION.

dIsclaIMers

NO EXPRESS WARRANTY HAS BEEN OR WILL BE MADE IN BEHALF 

OF THE WARRANTOR WITH RESPECT TO THE MERCHANTABILITY 

OF THE HEATER OR THE INSTALLATION, OPERATION, REPAIR OR 

REPLACEMENT OF THE HEATER OR PARTS. THE WARRANTOR 

SHALL NOT BE RESPONSIBLE FOR WATER DAMAGE, LOSS OF 

USE  OF THE  UNIT,  INCONVENIENCE,  LOSS  OR  DAMAGE TO 

PERSONAL PROPERTY, OR OTHER CONSEqUENTIAL DAMAGE. 

THE WARRANTOR SHALL NOT BE LIABLE BY VIRTUE OF THIS 

WARRANTY OR OTHERWISE FOR DAMAGE TO ANY PERSONS 

OR PROPERTY, WHETHER DIRECT OR INDIRECT, AND WHETHER 

ARISING IN CONTRACT OR IN TORT.

Some states do not allow the limitation or exclusion of incidental or 

consequential  damages,  so  the  above  limitation  or  exclusion  may 

not apply to you.

This warranty gives you specific legal rights, and you may also have other 

rights which vary from state to state. Should governmental regulations 

or  industry  standards  prohibit  the  Manufacturer  from  furnishing  a 

comparable model replacement under this warranty, the Owner will be 

furnished with the closest comparable water heater meeting the current 

governmental regulations and industry standards. A supplementary 

fee may be assessed to cover the additional cost associated with the 

changes made to meet applicable regulations and standards.
Fill out and keep with water heater.

IMportant InforMatIon

Model Number 

 __________________________________________

Serial Number 

___________________________________________

Installation Information:

Date Installed 

 ___________________________________________

Company’s Name 

 ________________________________________

Street or P.O. Box  ________________________________________

City, State, and Zip Code 

 __________________________________

Phone Number 

 ____________

  Plumber’s Name 

_______________

Summary of Contents for GP6 50 Series

























































Reviews: