FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to
www.startech.com/warranty
.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
7. Insert the
Mounting Screws
(x 2) through the
Mounting Holes
on the
PoE Injector
and into the
Wall
.
8. Using a
Phillips Head Screwdriver
, tighten the
Mounting Screws
until the
PoE
Injector
is securely fasten to the
Wall
.
Product Dimensions
1. Connect a
CAT5e/6 Cable
to the
PoE Out Port
on the
PoE Injector
and the other
end to an RJ45 port on a
PoE
PD Device
(e.g. security camera, etc.).
2. Connect a
CAT5e/6 Cable
to the
Data Port
on the
PoE Injector
and the other end to
an RJ45 port on a
Network Switch
.
Mounting
DIN Rail Mounting
1. Align the
DIN Rail Brackets
(x 1) with the
Mounting Holes
(x 4) on the side of the
PoE Injector
.
2. Insert the
Mounting Screws
(x 3) through the
DIN Rail Bracket
and into the
PoE
Injector
.
3. Using a
Phillips Head Screwdriver
, tighten the
Mounting Screws
. Be careful not to
over-tighten the
Mounting Screws
.
4. Clip the
DIN Rail Bracket
onto a
DIN Rail
, securing the
PoE Injector
.
Wall Mounting
It is recommended that you use
Wall Studs
when wall mounting the
PoE Injector
.
1. Align the
Mounting Brackets
(x 2) with the
Mounting Holes
(x 4) on the side of the
PoE Injector
.
2. Insert the
Mounting Screws
(x 4) through each of the
Mounting Brackets
and into
the
PoE Injector
.
3. Align the
PoE Injector
on the wall in the position you want to mount the
PoE
Injector
.
4. Using a
Writing Utensil
, mark off both
Mounting Holes
on the
PoE Injector
.
5. Using a
Level
, draw a line connecting the two
Mounting Holes
, making sure that the
line is level.
6. Align the
Mounting Holes
on the
PoE Injector
with the
Mounting Hole Marks
.
