Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 2, 2020 11:37 AM
Product Diagram (POEINJ1G90W)
Component
Function
1
Power LEDs
•
Green:
A
Power Source
is detected.
•
Off:
A
Power Source
is not detected.
2
PoE LED
•
Amber:
Indicates that the
PoE Injector
is
providing power.
•
Off:
Indicates that the
PoE Injector
is in idle
mode.
3
PoE Out Port
• Connect a
Powered Device
(PD) to the
PoE
Injector
.
4
Data Port
• Connect a
Network Switch
to the
PoE
Injector
.
5
4-Pin Terminal Block
V1 and V2
• Connect an external
DC Power Source
(48-56V
DC Input) to the
PoE Injector
.
6
Ground Screw
• Connect a ground connection to the
Ground
Screw
when connecting a
DC Power Source
to
the
PoE Injector
.
Requirements
For the latest requirements, please visit
www.startech.com/POEINJ1G90W
• Small Flat Head Screwdriver x 1
• (Optional) Phillips® Head Screwdriver x 1
• (Optional) Writing Utensil x 1
• PoE Powered Device (PD) x 1
• Network Switch x 1
• DC Power Source or Universal Power Adapter with Type N (OD: 5.5 mm, ID: 2.5 mm)
Barrel Connector x 1
90W Industrial Grade Hardened 802.3bt PoE Injector | 1G (1000 Mbps)
• RJ45 Terminated UTP/STP Cat 5e (or better) Network Cable x 2
Powering the PoE Injector
Terminal Block
Connecting and installing the
4-Wire Terminal Connector
, must be completed by a
licensed Electrician.
Notes:
Make sure that you turn off the power source before connecting the power wire
to the
PoE Injector
.
Do not exceed the recommend power source voltage as it may result in personal or
product damage.
1. Using a
Small Flat Head Screwdriver
, loosen the two screws (V1 or V2) on the
4-Wire Terminal Connector
(included).
2. Connect the
Power Wires
from a
DC Power Source
(48 - 56V DC), or the provided
Barrel Power Connector Adapter,
to the proper
Terminal Block Connectors
to
the terminals are marked on the
PoE Injector’s Casing
. Connect the positive wire to
V+ and the negative wire to V-.
3. Tighten the two screws on the
4-Wire Terminal Connector
.
4. Insert the
4-Wire Terminal Connector
in the
4-Wire Terminal Block
on the
PoE
Injector
.
5. To connect a second
Power Source
to the
PoE Injector
, repeat steps 1 - 4.
6. Using a
Phillips Head Screwdriver
, loosen the
Ground Screw
on the
PoE Injector
.
7. Connect the
Ground Wire
from a
DC Power Source
to the
Ground Screw
on the
PoE Injector
.
8. Using the
Phillips Head Screwdriver
, tighten the
Ground Screw
to secure the
Grounding Wire
to the
PoE Injector
.
(Optional) Barrel Connector
• Connect a
Type N (OD: 5.5 mm, ID: 2.5 mm) Barrel Connector
from a
Universal
Power Adapter
to the
Terminal Block to Barrel Power Connector Adapter.
Connecting the PoE Injector
Notes:
Make sure the total length of the
CAT5e/6 Cable
connecting the
PD Device
to the
PoE Injector
and the
CAT5e/6 Cable
connecting the
PoE Injector
to the
Remote Switch
does not exceed 100 meters in total length.
The
PoE Injector
is compatible with both Power over Ethernet (PoE) and 95W Power
over HDBaseT (PoH).
1
2
3
4
5
6
