background image

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:

•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void 

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may 

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation 

est autorisée aux deux conditions suivantes:  

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, 

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com.  Where they occur these references are for illustrative purposes only 

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which 

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered 

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the 

property of their respective holders.

Warranty Information

This product is backed by a lifetime warranty. 

For further information on product warranty terms and conditions, please refer to 

www.startech.com/warranty

.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) 

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of 

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.  

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations 

or exclusions contained in this statement may not apply to you.

Safety Measures

•  If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

•  Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension. 

安全対策

•  製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください

Misure di sicurezza

•  Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

•  Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT:  startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Crescent

London, Ontario 

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Road 

Brackmills,

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

StarTech.com Ltd.

Siriusdreef 17-27

2132 WT Hoofddorp

The Netherlands

Software Installation

Driver Installation

This product requires a driver to be installed on the 

Host Computer

. Download the 

latest 

Drivers 

from the StarTech.com website:  

www.startech.com/PCI2S1P2

.

Navigate to the 

Drivers/Downloads

 tab to locate the 

Drivers

. Follow the instructions 

included with the 

Driver Files

5.  Gently insert the 

PCI Card 

into the open 

PCI Slot

 and fasten the 

Bracket

 to the rear 

of the 

Computer Case

, using the 

Screw

 from step 4. 

6.  Locate a second open

 PCI Slot

 and remove the corresponding 

Metal Cover Plate

 

from the rear of the 

Computer Case

. In most instances, the 

Metal Cover Plate

 is 

attached to the rear of the

 Computer Case

 with a single 

Screw

. Save this 

Screw

 for 

the next step. 

7.  Fasten the 

Bracket (Parallel)

 to the rear of the 

Computer Case

, using the 

Screw

 

from step 6. 

8.  Place the 

Cover

 back onto the 

Computer Case

9.  Reconnect all of the 

Peripheral Devices

 that were disconnected in step 2.

10. Connect a 

Serial Device

 to the 

Serial Port

 on the 

PCI Card

.

11. Connect a 

SPP/EPP/ECP Peripheral Device

 to the 

Parallel Port

 on the

 PCI Card

.

12. Reconnect the 

Power Cable

 to the rear of the 

Computer

.

Reviews: