FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to
www.startech.com/warranty
.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Converter
.
3. Using a
Phillips Head Screwdriver
, tighten the
Mounting Screws
. Be careful not to
over-tighten the
Mounting Screws
.
4. Clip the
DIN Rail Bracket
onto a
DIN Rail
, securing the
Media Converter
.
Wall Mounting
It is recommended that you use
Wall Studs
when wall mounting the
Media
Converter
.
1. Align the
Mounting Brackets
(x 2) with the
Mounting Holes
(x 4) on the side of the
Media Converter
.
2. Insert the
Mounting Screws
(x 4) through each of the
Mounting Brackets
and into
the
Media Converter
.
3. Align the
Media Converter
on the wall in the position you want to mount the
Media Converter
.
4. Using a
Writing Utensil
, mark off both
Mounting Holes
on the
Media Converter
.
5. Using a
Level,
draw a line connecting the two
Mounting Holes
, making sure that
the line is level.
6. Align the
Mounting Holes
on the
Media Converter
with the
Mounting Hole
Marks
.
7. Insert the
Mounting Screws
(x 2) through the
Mounting Holes
on the
Media
Converter
and into the
Wall
.
8. Using a
Phillips Head Screwdriver,
tighten the
Mounting Screws
until the
Media
Converter
is securely fastened to the
Wall
.
Product Dimensions
2. Connect the
Power Wires
from a
DC Power Source
(12 - 56V DC), or the provided
Barrel Power Connector Adapter,
to the proper
Terminal Block Connectors
on
the
Media Converter
. The terminals are marked on the
Media Converter’s Casing
.
Connect the positive wire to V+ and the negative wire to V-.
3. Using a
Small Flat Head Screwdriver
, loosen the screw for the
Ground Connection
on the
3-Wire Terminal Connector
.
4. Connect the
Ground Wire
from an
Earth Ground Connection
to the
Ground
Connection
on the
3-Wire
Terminal Connector
.
5. Tighten the three screws on the
3-Wire Terminal Connector
.
6. Insert the
3-Wire Terminal Connector
in the
3-Wire Terminal Block
on the
Media
Converter
.
(Optional) Barrel Connector
• Connect a
Type N (OD: 5.5 mm, ID: 2.5 mm) Barrel Connector
from a
Universal
Power Adapter
to the
Terminal Block to Barrel Power Connector Adapter.
Connecting the Media Converter
1. Connect a
CAT5e/6 Cable
to the
RJ45 Port
on the
Media Converter
and the other
end to an RJ45 port on a
Network Device
.
2. Insert an
MSA-Compliant SFP Transceiver Module
(sold separately) into the
SFP
Slot
on the
Media Converter
.
3. Remove the
Dust Cover
from the
SFP Module
and connect the appropriate cable
(CAT5e/6 or Fiber).
Mounting
DIN Rail Mounting
1. Align the
DIN Rail Brackets
(x 1) with the
Mounting Holes
(x 4) on the side of the
Media Converter
.
2. Insert the
Mounting Screws
(x 3) through the
DIN Rail Bracket
and into the
Media
