Start italiana Digimon TFT Installation Manual Download Page 3

      

                  

Digimon TFT rev.01  2014/05 - ENG

 

 

 

 

 

INTRODUCTION 

 
The handbook gives all the instructions for installation and use of DGM console. 
 

 
 

 

This product complies with EU Directive 2012/19/UE.  
The crossed-bin symbol on the device indicates that the product, at the end of its lifecycle, should be disposed separately 
from household waste, must be brought to a electrical and electronic equipment collection point. 

 
 

Note: Start Italiana Srl, in respect of its quality duties may modify its production and the data shown on this handbook. This 
manual cannot be reproduced, totally and neither partially, without authorization. 

 
 
 

GENERAL WARNINGS 

 

 

Please read carefully the instructions given in this handbook before working on this equipment. 

 

The manufacture is not responsible of any operation performed not mentioned in this handbook.  

 

In case of failure or faulty operations, please refer to authorized people in charge for maintenance or directly to the manufacturer. 

 

The manufacturer refuses all responsibility for any eventual injury and/or damage to things caused by the missing observation of 
safety requirements. 

 

The assigned personnel is required to know all the safety requirements relative to this equipment. 

 

In  case  of  doubts  about  functioning  of  the  equipment  please  refer  to  authorized  people  for  maintenance  or  directly  to  the 
manufacturer. 

 

Every tampering of the equipment relieves the manufacturer from any responsibility in front of competent authorities. 

 

 

 

 

This product is used in fuel tanks and in hazardous areas for risk of explosion and fire. Subterranean leakage of fuel tanks may cause 
serious damages to environment and injury. 
 

Summary of Contents for Digimon TFT

























Reviews: