background image

Handbook for the TRIUS PRO 694      Issue 19th April 2019 

 

 

21 

 

Dear Observer, 

Thank you for purchasing a Starlight Xpress CCD Imaging System. We are confident that you will gain 

much satisfaction from this equipment, but please read carefully the accompanying instruction 

manual to ensure that you achieve the best performance that is capable of providing. 
As with most sophisticated equipment a certain amount of routine maintenance is necessary to keep 

the equipment operating at its optimum performance. The maintenance has been kept to a minimum, 

and is fully described in the manual. 
In the unfortunate instance when the equipment does not perform as expected might we recommend 

that you first study the fault finding information supplied. If this does not remedy the problem, then 

contact Starlight Xpress for further advice. Our message board service on the Starlight Xpress web site 

will normally provide a rapid response to any problems that you encounter. 
The equipment is covered by a 12-month guarantee covering faulty design, material or workmanship 

in addition to any statutory Consumer Rights of Purchasers. 

CONDITIONS OF GUARANTEE 

1) The equipment shall only be used for normal purposes described in the standard operating 

instructions, and within the relevant safety standards of the country where the equipment is used. 
2) Repairs under guarantee will be free of charge providing proof of purchase is produced, and that 

the equipment is returned to the Service Agent at the Purchaser’s expense and risk, and that the 

equipment proves to be defective. 
3) The guarantee shall not apply to equipment damaged by fire, accident, wear an tear, misuse, 

unauthorised repairs, or modified in any way whatsoever, or damage suffered in transit to or from the 

Purchaser. 
4) The Purchaser’s sole and exclusive rights under this guarantee is for repair, or at our discretion the 

replacement of the equipment or any part thereof, and no remedy to consequential loss or damage 

whatsoever. 
5) This guarantee shall not apply to components that have a naturally limited life. 
6) Starlight Xpress’s decision in all matters is final, and any faulty component which has been replaced 

will become the property of  Starlight Xpress Ltd. 
 
For further info. or advice, please call: 
Mr Michael Hattey, 
Starlight Xpress Ltd., 
Unit 3, Brooklands Business Park, 
Bottle Lane, 
Binfield 
Berkshire, 
England.  RG42 5QX 
Tel: 01184026898 
Email: 

[email protected]

  

Web site: 

http://www.sxccd.com 

 

 

 

Summary of Contents for TRIUS PRO 694























Reviews: