Star-Oddi DST microRF-HRT User Manual Download Page 6

Page: 6 / 42

User Manual

Gná Graphic Supporting Software

Page 6

Mercury & Gná program

installation

Mercury & Gná is an online user software for the Star-Oddi telemetry system.

Mercury & Gná can run under Windows 2000 or newer. The following chapters will

take you step-by-step through the program installation, hardware connections and use

of the Mercury & Gná Program.

The installation of Mercury & Gná requires access to a PC computer with a standard

RS-232C serial interface or USB.

The users of Mercury & Gná will receive free updates of the software. Updates of

Mercury & Gná will be available for free download at:

http://www.star-oddi.com/Downloads/

The Star-Oddi telemetry logger is supported by the Mercury software and the

Communication Box, which works as an interface between the logger and the

computer. The logger is ready for recording after the user has set the start time and

sampling interval in the Mercury software. The recorded data is transmitted to Gná

where the results can be analyzed in graphic and tabular form. In Gná the user has the

option to print out reports with information such as energy consumption of the RF

boxes.

This chapter describes how to install and uninstall the Mercury & Gná software on

your PC computer. Please note that each software needs to be installed and

uninstalled separately.

2.1

Install

To download Mercury & Gná visit www.star-oddi.com/downloads. To install the

program, follow the automatic InstallShield Wizard.

Follow the instructions on the screen. You will be prompted for a directory name for

your Mercury & Gná program.

Type in your product key. Please keep the product key in a safe location as you may

need it for future use. The product key works for multiple computers on the same

network.

Distributed by MicroDAQ.com, Ltd. www.MicroDAQ.com (603) 746-5524

Summary of Contents for DST microRF-HRT










































Search results

Summary of Contents for DST microRF-HRT

Reviews:

Star-Oddi DST microRF-HRT, User Manual, Page: 6 / 42

Search results

Summary of Contents for DST microRF-HRT

Reviews: