Star Micronics NP-215 Specifications Download Page 18 | Manualshive

Page: 18 / 45

Star Micronics NP-215 Specifications Download Page 18

15

8. CN8 Connect to operation panel

Printer side connector: 53047-0310(Molex)

Mating

connector

51021-0300(Molex)

Pin# Signal

name In/Output

Functions

Remarks

1

/LF

Input

Paper feed signal input

Active at L

2 ALM Output

Printer

error

signal

Output

Output in
printer error

3 SG

-

Signal

ground

1) Paper feed is executed according to the paper feed pitch set by ESC 2, ESC 3. However, if

there is no paper, line feed is not executed.

2)  While paper feed signal is at “L”, set Power on to activate self-diagnostic printing.
3)  While paper feed signal is at “L”, release INIT signal to “H” to activate diagnostic printing.
4)  ALM signal (for operation panel) indicates printer statuses as follows:

A protective resistance is incorporated on the board, a light diode can be located between
2 and 3. 2: anode and cathode.

Display pattern

Printer status

How to solve the problem

1
0

Normal status
Print (receive) ready

No paper

Load the paper

1
0

Head up status

Set head down

F/W write mode

Set the power on again

1
0

Presenter in cramp status

Pull out the clamped paper

Head temp high (80

˚

c)

Printer returns normal at head temp of
60

˚

c

1

0

Wrong head connection

Connect head cable properly

Auto-cutter error

1
0

Presenter error

Remove jammed paper and turn
power on again, or input INIT signal

9. CN9 Connect to presenter (NPT-301 only)

Printer side connector: 53047-0810

Mating

connector:

51021-0800

* Connect to NPT-301 only. When connect to other product, it would cause problems.

Pin #

Signal

Input/output

Remarks

6

LED +

Output

To sensor LED1

7

Sensor 1

Input

From sensor 1

8 SG

- Signal

GND

9

LED2 +

Output

To sensor LED2

10 Sensor2

Input From sensor2

11 SG

- Signal

GND

12

M +

Output

Motor drive output

13

M -

Output

Motor drive output

«
...
16
17
18
19
20
...
»

Summary of Contents for NP-215














































Reviews:

No comments