Star Micronics IFBD-BE07 User Manual Download Page 53

Page: 53 / 89

IFBD-HE0708 BE07 User’s Manual

3-44

3.3.9. Printer Status Display

• The printer automatic status is displayed in a hexadecimal dump by HTTP (WEB), TELNET, and FTP.

Display Example

• Other status details of the hexadecimal dump display are displayed by HTTP (WEB).

The displayable status information is shown below.

* See the printer’s specifications manual for details on status specifications.

Status Information

Display

Status

Ready

Idling

Not Ready

Error status

Not Ready Causes

Cover Open

Cover open

Paper Empty

Paper out

Paper Near End

Paper near-end

Paper Size Error (Black Mark/ Label Error)

Black mark error (models that support BM)/

label size error (models that support labels)

Auto Cutter Error

Auto-cutter Error

Presenter Paper Jam Error

Paper jam at presenter

Mechanical Error

High Temperature Detection

High temperature stop

Non-recoverable Errors

Non-recoverable Error

Display Example

Summary of Contents for IFBD-BE07


























































































Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands

Star Micronics IFBD-BE07, User Manual

Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands