Stanton M.505 User Manual Download Page 10

WARRANTY & RETURN POLICY

Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement

Warranty

Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the

U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or provid-

ing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) follow-

ing the date of original purchase. Exceptions to this warranty are as noted below:

The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days

following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000;

and Switches - 10,000.

Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made

necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Returns

Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requir-

ing warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton deal-

er from whom the merchandise was purchased and in the same country where the merchandise was purchased. For pur-

poses of purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the coun-

try where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton

dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns to

a non-authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to

be sold or as set forth above will void this warranty.

To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise,

and follow such authorized Stanton dealer’s return policy.

Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or applica-

tion made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringe-

ment of any rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by

Stanton from your purchase of such merchandise. In no event will Stanton be liable for any special, incidental or conse-

quential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negli-

gence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims

any express or implied warranties of merchantability or fitness for a particular purpose.

The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to vari-

ation from state to state and country to country.

If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above,

please include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth

herein.

Please register your product online at www.stantondj.com or mail your completed warranty card to:

Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.

Summary of Contents for M.505













Reviews: