background image

20

21

TROUBLE SHOOTING

POSSIBLE CAUSE

SUGGESTED FIX

Engine will not start

No or low fuel in the fuel tank

Fill fuel tank

No or low oil in sump

Fill oil sump

Fuel/Engine lever is OFF

Turn fuel/engine lever ON

Choke is set to RUN

Slide choke to START

Pressurised pump

Turn water tap off, pull trigger to release water from pump.  
Start motor, then turn water tap on

Unit does not reach high pressure

Diameter of garden hose is too small

Replace with a 12mm garden hose

Water supply is restricted

Check garden hose for kinks, leaks and blockage

Water inlet filter is clogged

Open water source to full force

Black detergent nozzle is attached

Remove detergent nozzle and attach a high pressure nozzle

Not enough inlet water supply

Check garden hose for kinks, leaks and blockage

Output pressure varies high and low

Pump is sucking air

Check garden hose for kinks, leaks or blockage. 
Check whether hoses and fittings are air tight

Water inlet filter is clogged

Turn off machine and purge pump by squeezing trigger gun
until a steady flow of water emerges through the nozzle

Discharge nozzle is obstructed

Remove filter and rinse out in warm water

Calcified gun, hose or spray wand

Blow out or remove debris with a fine needle. Run
distilled vinegar through detergent suction tube

No detergent

Detergent suction tube not properly
connected to the machine

Check connection

Detergent is too thick

Dilute detergent

Garden hose connection leaks

Filter on detergent suction tube is clogged

Run warm water through filter to remove debris

Damaged or clogged detergent suction tube

Remove obstruction or replace detergent suction tube

Spray wand leaks

A high pressure nozzle is attached

Replace with black detergent nozzle

Discharge nozzle is obstructed

Blow out or remove debris with fine needle

Leaky connection

O-ring is worn, replace

Pump is noisy

Loose fittings

Tighten fittings. Insert  new washer.
Ensure spray wand is tight onto the gun

Spray wand not properly attached

Tighten the spray wand onto the gun. Turn the wand
collar clockwise onto the gun threads until tight

Water leaks from pump

Pump is sucking air

Check whether hoses and fittings air tight. Turn off machine
and purge pump by squeezing trigger gun until a steady
flow of water emerges through nozzle

Loose fittings

Check that all fittings are tight

Oil Drop

Oil seals are damaged or worn

Call service centre

Summary of Contents for SXPW7032BS

























Reviews: