Stanley SXPW1451BS Manual Download Page 15

14

15

STARTING YOUR PRESSURE WASHER

1.  Check oil level.
2.  Check and fill fuel. 
3.  Connect garden hose to cold water source.  

Do not turn on! 

4.  Connect garden hose to garden connection on pump.
5.   Select nozzle, see page 13
6.  If using detergent fill and select bottle refer page 14, 

Pic. 10.

7.  Turn choke to start by sliding the choke lever to the 

LEFT, Pic 12.

8.  Slide the fuel lever to ON by sliding the fuel lever  

to the right, Pic 11.

9.  Push engine switch to “1”, refer Pic. 13.
10. Pull the recoil starter slowly until engaged, then 

pull briskly. This step may need to be repeated until 

pressure washer engine starts, this can take up to 

about 12 pulls, Pic 14.

Warning:

 Never pull the recoil once the engine  

has started. Any damage caused will not be covered  

under warranty.

11. Once started turn choke to off (run), slide to RIGHT, 

refer Pic. 11.

12. Turn cold water source on.  
13. Release safety lock on trigger, push lever down.
14. Squeeze trigger on wand.  Hold down until all air 

is purged and a steady stream of water is passing 

through, Pic 15. 

15. Release trigger to stop water flow. 

WHEN FINISHED WITH DETERGENT

When finished with detergent, release trigger on wand. 

Remove tube and filter from detergent bottle. Place tube 

and filter around handle.  Do not place on the ground as 

this will suck dirt into pump. Any damage caused will not 

be covered under warranty. 
Change nozzle, see page 13.
Squeeze trigger and continue cleaning with clean  

cold water.

STOPPING YOUR PRESSURE WASHER

To stop your pressure;

1.   Turn cold water supply off.
2.   Squeeze gun trigger, releases some water and pressure.
3.   Turn fuel tap off, to left, refer Pic. 12.
4.   Push engine switch off “0”.
5.   Once engine has stopped, squeeze gun trigger, releases 

some water and pressure.

6.   Disconnect the garden hose from pressure pump and 

garden tap.

7.   Lock the gun, push lever up.
8.   Tidy up hose, gun and lance.
9.   Allow pressure washer to cool about 1 hour before 

wiping down and store appropriately.

PIC. 15

PIC. 12

CHOKE 

OFF

CHOKE 

ON

PIC. 11

PIC. 13

Starting Handle

PIC. 14

FUEL ON

FUEL OFF

Summary of Contents for SXPW1451BS

























Reviews: