Stanley SXEW159501 Manual Download Page 12

12

13

WARNING:  THIS UNIT IS INTENDED TO BE USED WITH  

COLD WATER ONLY! DO NOT USE HOT WATER IN THIS 
PRESSURE CLEANER!

STARTING AND STOPPING YOUR PRESSURE CLEANER

Never switch your pressure cleaner ON unless the water has 
been turned on and connected to the pressure cleaner first.

Your pressure cleaner is equipped with an automatic on/off 
switch. The pressure cleaner will only run when the power 
switch is in the ON position and the trigger on the gun is 
squeezed, with water flowing through. When you release the 
trigger to stop spraying water through the gun, the motor will 
automatically shut off. Simply squeeze the trigger again to 
resume using the cleaner. Always ensure that you plug your 
pressure cleaner into a standard 240V AC power point.

OPERATING SWITCH

To turn your pressure cleaner ON, rotate the switch to ‘ON/l’. 
To turn your pressure cleaner OFF, push the switch to’OFF/0’.

GUN SAFETY LOCK (PIC. 8)

This pressure cleaner is equipped with a gun trigger safety lock. 
When not using the pressure cleaner, use the safety lock to 
keep from accidentally engaging the high pressure spray.

BLEEDING THE PRESSURE WASHER SYSTEM

It is very important to bleed the gun before using the  
pressure cleaner.

To bleed the gun, simply connect the garden hose to the 
pressure cleaner and squeeze the trigger BEFORE turning the 
electrical supply on. This allows any air trapped inside the 
pressure cleaner and gun to be removed before using the unit. 
Continue holding trigger for approximately one minute to allow 
any excess air out of the unit. Water will flow through the gun at 
low pressure during this procedure.

TO START USING

1.   Ensure your pressure washer is fully assembled, including 

the lance and nozzle.

2.   Ensure the high pressure hose is firmly connected to the 

units outlet.

3.   Connect your water hose to the pressure cleaner inlet.
4.   Connect your water hose to the mains tap and turn on. 
5.   Un-lock the safety gun lock.
6.   Bleed the pressure washer system.
7.   Connect your pressure cleaner to a 240V AC power outlet 

and turn on.

8.   Switch pressure cleaner ON.
9.   Pick up gun, point at object to be cleaned and  

squeeze trigger.

NOTE:  The unit should be turned completely OFF while not in 
use or while unattended.

PIC. 8

OPERATING INSTRUCTIONS

Summary of Contents for SXEW159501

















Reviews: