SPECIFICATIONS AND TYPES OF MATERIALS AVAILABLE BY PART NUMBER
Part Number
Per
Strip #
Per
Box #
Material Wire
Diameter
Ring I.D. Ring Leg
Opening
Operating Range of
Tool SC50T
RING11RG40 40 1,600
Light
Galvanized
0.120
1.53
1.10
.410 - .465
RING11AL40 40 1,600
Aluminum
0.120
1.53
1.10
.410 - .465
RING11G40
40
1,600
High Tensile Galvanized
0.120
1.53
1.10
.460 - .513
RING11SS40
40
1,600 High Tensile Stainless Steel
0.120
1.53
1.10
.425 - .495
* Please specify “Blunt” or “Sharp” when ordering rings.
RING DOES NOT CLOSE COMPLETELY
1.
Check air pressure. Line pressure at the tool should be between 100 and 105 psi (6.90 - 7.24 bar) for most applications. The tool should
never be operated at pressures exceeding 115 psi (7.93 bar).
1.
A 3/8” (9.5 mm) or larger air line should be used with the “SC” Series Tools. Air lines in excess of 100’ (30.5 meters) in length can
cause air volume deficiencies at the tool which will prevent normal operation.
2.
Check for foreign debris in the jaw area. This is especially true in the area between the side plates and rollers.
3.
The jaws may be worn from extended use. Check the “land” between the receiving grooves of the jaws. If the land is worn excessively,
replacing the jaw(s) is recommended.
4.
When the tool is used in corrosive applications, light oil should be applied on a regular basis to the jaw bushings and rollers.
Unlubricated and/or corroded jaw bushings may cause the tool to function poorly.
5.
When ring teardrops, the latch is not backing the ring up properly. Replace or reshape latch spring to hold latch against the side plate.
The latch may also need replaced to get proper ring shape.
FEEDING PROBLEMS
1.
If rings do not feed smoothly down the magazine, check pusher spring for proper tension. If the magazine is covered with dirt from field
use, clean the magazine and apply a light coating of oil.
1.
When rings feed properly on the magazine but do not feed into the jaws without spitting out of the magazine side of the tool, or if the
rings sit in the jaw grooves on an angle, check jaws to insure freedom of movement. With the jaws void of rings, the vertical movement
should be approximately .09” (2.3 mm). The jaw bolt nuts should be snug, but
never over-tightened
.
2.
After considerable use or several jams, the fingers on the pusher may show signs of spreading. This may cause the pusher to “hang up”
on the magazine, with little or no pressure behind the rings. The last few rings in the strip will not feed into the jaw mechanism. The
pusher fingers can be squeezed back into proper position or the pusher should be replaced.
NEVER USE LOOSE RINGS IN THE SC
TOOL.
LIMITED WARRANTY
Stanley Fastening Systems warrants to the original retail purchaser that this product is free from defects in material and
workmanship, and agrees to repair or replace, at Stanley Fastening Systems’ option, any defective product within 60 days
from the date of purchase. This warranty is not transferable. It only covers damage resulting from defects in material or
workmanship, and it does not cover conditions or malfunctions resulting from normal wear, neglect, abuse, or accident.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THIS
WARRANTY. STANLEY FASTENING SYSTEMS SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
To obtain warranty service, you must return the product at your expense together with the proof of purchase to a Stanley-
Bostitch Regional warranty repair center or you may call us at 1-800-556-6696 or 1-800-832-3080 for the location of
additional authorized warranty service locations in your area.
6
of
6
01/03