Stanley Fatmax FME190, Original Instructions Manual

Page: 7 / 88

6
ENGLISH (Original instructions)
7
ENGLISH (Original instructions)
Note! Tighten the connection hand tight at first, before using
the spanners.
Removing/Replacing (Fig.E, Fig.F)
u
Lock the socket (3) with one mounting spanner (9) and
loosen the shaft (4) anticlockwise with another mounting
spanner (9) gripping the welded nut (Fig. E).
u
Loosen the welded nut anticlockwise (Fig. F) and remove
the shaft (4) from the socket (3) (Fig. F)
Stirrer (Fig.G, Fig.H)
u
Lock the welded nut of the shaft (4) with one mounting
spanner (9) and loosen the stirrer (5) anticlockwise with
another mounting spanner (9) gripping the welded nut
(Fig. G).
u
Loosen the welded nut anticlockwise (Fig. H) and remove
the stirrer (5) from the shaft (4) (Fig. H).
u
Attach a new shaft/stirrer as required.
Use
Variable speed switch (Fig.I)
Operate the product either in instant or continuous mode.
Instant Mode
u
Switch the product on by pressing the variable speed
switch (7) (Fig. I).
u
Switch the product off by releasing the variable speed
switch (7).
Continuous mode
u
Switch the product on by pressing the variable speed
switch (7) and hold it in position (Fig. J, step 1).
u
Press the lock-on button (6) and hold it in position to lock
the variable speed switch (7) (Fig. I, step 2).
u
Release the lock-on button (6) and variable speed switch
(8). The variable speed switch is now locked on for
continuous use.
u
Depress and release the variable speed switch (7) to
switch the product off.
General operation
u
Check the product, its power cord and plug as well as
accessories for damage before each use. Do not use the
product if it is damaged or shows wear.
u
Double check that the accessories and attachments are
properly fixed.
u
Always hold the product on its handles. Keep the handles
dry to ensure safe support.
u
Ensure that the air vents are always unobstructed and
clear. Clean them if necessary with a soft brush. Blocked
air vents may lead to overheating and damage the
product.
u
Switch the product off immediately if you are disturbed
while working by other people entering the working area.
Always let the product come to complete stop before
putting it down.
u
Do not overwork yourself. Take regular breaks to ensure
you can concentrate on the work and have full control over
the product.
Mixing (Fig.K)
Warning! During operation fine dust will be generated!
Some dusts are highly inflammable and explosive! Do not
smoke during operation, keep heat sources and open flames
out of the working area! Always wear a dust mask to protect
yourself against hazards resulting from fine dust!
The stirrer will come to a stop during operation if the material
is too firm! Switch the product off, lift the stirrer out of the
material and inspect the material before using the product
again! A blocked stirrer may cause overheating the of the
motor. Hold the product firmly during operation. Do not let the
stirrer touch the bucket! This can cause damage to the stirrer
and bucket!
u
Hold the product with 2 hands on both handles (2) and
insert the stirrer (5) into the material (Fig. M).
u
Gently press variable speed trigger switch to start
operation at a low speed.
u
Move the stirrer through the material until it is evenly and
completely mixed.
u
Switch the product off. Let the stirrer come to a complete
stop before lifting it out of the mixing material.
Warning: Switch the product off, let it come to a complete
stop and disconnect it from the power supply if the stirrer
gets stuck in the mixing material. Only then free the jammed
attachment.
After use
Warning: Always switch the product off, disconnect the
product from the power supply and let the product cool down
before performing inspection, maintenance and cleaning work!
Cleaning
u
Keep the product clean. Remove debris from it after each
use and before storage.
u
Regular and proper cleaning will help ensure safe use and
prolong the life of the product.
u
Inspect the product before each use for worn and
damaged parts. Do not operate it if you find broken and
worn parts.
Warning: Only perform repairs and maintenance work
according to these instructions! All further works must be
performed by a qualified specialist!
u
Clean the product with a dry cloth. Use a brush for areas
that are hard to reach.