background image

7

6

ENGLISH

(Original instructions)

u

Move charger and battery pack to a location where the 

surrounding air  temperature is approximately 65°F 

- 75°F (18°- 24°C).

u

If charging problems persist, take the tool, battery pack 

and charger to your local service center.

u

The battery pack should be recharged when it fails to 

produce sufficient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these 

conditions. Follow the charging procedure. You may also 

charge a partially used pack whenever you desire with no 

adverse affect on the battery pack.

u

Foreign materials of a conductive nature such as, but 

not limited to, steel wool, aluminium foil, or any buildup 

of metallic particles should be kept away from charger 

cavities. Always unplug the charger from the power supply 

when there is no battery pack in the cavity. Unplug charger 

before attempting to clean.

u

Do not freeze or immerse charger in water or any other 

liquid.

Warning!

 Do not allow any liquid to get inside charger. Never 

attempt to open the battery pack for any reason.  

If the plastic housing of the battery pack breaks or cracks, 

return to a service center for recycling.

Charger Diagnostics (Fig.B)

Refer to the indicators in figure B for the charge status of th

battery pack.

Bad Battery

If you see a bad battery blink pattern, do not continue

to charge this battery. Return it to a service center or a

collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life. A cold battery pack will charge at a 

slower rate than a warm battery pack. The pack will charge at 

that slower rate throughout the entire charging cycle and will 

not return to maximum charge rate even if the pack warms.

Fitting and removing the battery 

(fig. C, D

u

To fit the batter , line it up with the receptacle on the tool. 

Slide the battery into the receptacle and push down until 

the battery snaps into place, as shown in figure C

u

To remove the battery, push the release button (4a) while 

at the same time pulling the battery out of the receptacle, 

as shown in figure D

Use

Warning!

 Let the tool work at its own pace. Do not overload.

Switching on and off

u

To switch the torch on press in the switch (1)

u

To switch the torch off press in the switch (1)

The pivoting lens (fig. E, F

u

For your convienience, the lens can be pivoted into a 

range of positions.

u

Turn the pivoting LED wheel (3) anti clockwise and posi-

tion the Llens (2) as required.

Maintenance

Your Stanley FatMax tool has been designed to operate 

over a long period of time with a minimum of maintenance. 

Continuous satisfactory operation depends upon proper tool 

care and regular cleaning.

 

Your charger does not require any maintenance apart from 

regular cleaning.

Warning!

 Before performing any maintenance on the tool, 

remove the battery from the tool. Unplug the charger before 

cleaning it.

u

Regularly clean the ventilation slots in your tool and 

charger using a soft brush or dry cloth.

u

Regularly clean the motor housing using a damp cloth.

u

Do not use any abrasive or solvent-based cleaner.

u

Regularly open the chuck and tap it to remove any dust 

from the interior.

Protecting the environment

Z

Separate collection. Products and batteries 

marked with this symbol must not be disposed of 

with normal household waste..

Products and batteries contain materials that can be recov-

ered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according to 

local provisions. Further information is available at

www.2helpU.com

Technical data

FMCL001B

Voltage

18V

Lumens

650/

1900

Battery

FMC689L

FMC687L

FMC688L

Voltage           V

DC

18

18

18

Capacity         Ah

1.5

2.0

4.0

Type

Lithium-Ion

Lithium-Ion

Lithium-Ion

Charger

905998** typ.1

906086** typ.1

Input voltage V

AC

230

230

Output voltage V

DC

18

18

Current            A

1

1

Approx. charge time

90 - 240 min

45 - 120 min

ENGLISH

(Original instructions)

Australia & New Zealand

 

Stanley Black & Decker

St
www.blackanddecker.com.au 
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ) 

Reviews: