Stairmaster GAUNTLET Series 8 Service Manual Download Page 12

Page 12

Dessa säkerhetsföreskrifter är riktade till dig som är ägare av utrustningen. Av säkerhetsskäl är det ditt ansvar att utbilda alla 

medlemmar och träningspersonal så att de följer dessa säkerhetsföreskrifter. 

GÖR DETTA 

 • Instruera medlemmarna att gå igenom en 

läkarundersökning innan de börjar med något träning-

sprogram. Om du vid något tillfälle under träningen 

känner dig svimfärdig, yr eller upplever smärta, ska du 

konsultera din läkare.

 • Se till att du innan användning av maskinen har läst, 

förstått och följer alla varningar, instruktioner och pro-

cedurer för maskinen och i den här handboken.

 • Använd endast maskinen på det sätt som är avsett och 

som beskrivs i den här handboken. 

 • Ställ upp maskinen på en stabil och plan yta.

 • Inspektera maskinen så att där inte finns felaktiga, ut-

slitna eller lösa delar. Dessa måste du i så fall korrigera, 

ersätta och skruva åt före användning.

 • Sluta att använda maskinen om du känner dig yr, svim-

färdig eller utmattad.

 • Var försiktig när du stiger upp på eller ner från maski-

nen och se till att den har stannat helt innan du stiger 

upp eller ner från den.

 • Genomför regelbundet förebyggande underhåll enligt 

instruktionerna i handboken.

 • Se till att luftintagen är fria från hår, ludd och annat.

 • Se till att ytan på bältet är ren och torr.

 • Flytta pedalen på den sida du stiger upp eller ner till 

dess lägsta position och se till att maskinen har stannat 

helt innan du stiger upp eller ned från den.

 • Minska hastigheten för pedalerna/vevaxeln på ett 

kontrollerat sätt - den här enheten är inte utrustad med 

frihjul.

 • Innan du använder maskinen måste du läsa, förstå och 

testa proceduren för NÖDSTOPP.

 • Se till att elkabeln inte är i närheten av alltför heta 

värmekällor.

 • Koppla ur all strömtillförsel före underhåll och 

rengöring.

GÖR INTE DETTA 

 • Låt inte barn använda maskinen. Övervaka han-

dikappade och rörelsehindrade personer som 

använder sin maskin.

 • Överskrid inte den maximalt tillåtna vikten för an 

vändare(350 lbs. / 159 kg).

 • Använd inte maskinen utan gymnastikskor.

 • Bär inte löst sittande kläder eller kläder som kan 

fastna.

 • Stig inte på och hoppa inte av maskinen när den är 

i rörelse. 

 • Använd inte den här maskinen på fuktiga eller 

blöta platser.

 • Sätt inte in och tappa inte någonting och ha inte 

någon hand eller fot i någon öppning eller under 

den här maskinen.

 • Placera inte vattenflaskor eller koppar på den här 

maskinen om du inte använder de hållare som är 

avsedda för detta. 

 • Använd inte maskinen på sådana ställen där aero-

solspray används eller där syrgas används.

 • Anslut inte någonting som tillverkaren inte har 

rekommenderat.

 • Använd inte maskinen med borttagen motorhuv 

och gör inte om maskinen på något sätt.

 • Använd inte maskinen om elkabeln eller kontak-

ten är skadad eller om den inte fungerar normalt, 

om den har tappats eller blivit skadad eller om 

skärmen visar en felkod.

VARNING: LÄS HELA  
ÄGARHANDBOKEN INNAN DU 
ANVÄNDER DEN HÄR MASKINEN.

VARNING: kOPPLA UR ELKABELN 
FÖRE RENGÖRING OCH 
UNDERHÅLL.

VARNING: DET FINNS RÖRLIGA 
DELAR. HA INTE HÄNDER ELLER 
FÖTTER UNDER MASKINEN NÄR 
DEN ANVÄNDS.

STOPPA (AKTIVITETEN)

AV

FÖRSIKTIGHETSÅTGÄRDER

Summary of Contents for GAUNTLET Series 8























































Reviews: