background image

222936 / YL6060300020

2018-04-13·BA00·III·en·01

Mounting and installation  

11

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

Explosion Proof Combination Signal - 

110 dB (A) / 5 Joule

Series YL60

7.2

Mounting / dismounting, operating position

• Mount the device on a flat surface suitable for its weight.

• The tone output should be directed towards the area to be covered  

(see chapter Technical Data, Polar diagram).

• Insert the cables using certified and flameproof cable glands which are suitable for the 

gas group.

• Close unused entries using certified and flameproof stopping plugs.

7.2.1 Installation conditions for electrical connection

DANGER

Risk of explosion! 

Risk of injuries and material damage!

• Terminal sleeves are fitted, they must be gas-tight and applied with a 

suitable tool.

DANGER

Explosion hazard! 

Risk of injuries and material damage!

• Carefully remove or replace the components.

• Exposed joint surfaces must not be damaged and must be protected 

from dust and dirt.

• Install the end flanges squarely without applying any force. Do not use 

a hammer or other tools when working on the flanges and do not use the 

fixing screws to pull down the flanges.

DANGER

Explosion hazard! 

Risk of injuries and material damage!

• Only use cable glands with corresponding certificate. The cable glands 

must be flameproof (Ex d) and suitable for the type of cable used.

• Close unused open holes in the enclosure with flameproof stopping 

plugs.

• Close unused cable glands using flameproof plugs.

• Cable glands, stopping plugs and plugs must meet the requirements of 

IEC/EN 60079-14.

• Installation of the cable gland must be performed in accordance with the 

manufacturer's instructions.

• Cable entry temperature may exceed 70 °C.

• To ensure degree of protection IP 66, a non-hardening sealant must be 

applied to the threads.

DANGER

Danger due to energised parts! 

Non-compliance results in severe or fatal injuries.

• Before opening and dismounting the device, disconnect it from the  

power supply.

• Secure the device against unauthorized switching. 

Summary of Contents for YL60 Series



























Reviews: