background image

USER MANUAL

 

 

7

GENERAL SAFETY INSTRUCTIONS 

 

Every person involved with installation and maintenance of this device have to: 

z

 Be 

qualified 

z

 

Follow the instructions of this manual 

 

 

 

 

 

This device has left out premises in absolutely perfect condition. In order to 

maintain this condition and to ensure a safe operation, it is necessary for the user 

to follow the safety instructions and warning notes written in this manual. 

 

         

Important!   

The manufacturer will not accept liability for any resulting 

damages caused by the non-observance of this manual or 

any unauthorized modification to the device. 

 

z

 

Please consider that damages caused by manual modifications to the 

devise are not subject to warranty. 

z

 

Never let the power-cord come into contact with other cables! Handle the 

power-cord and all connections with the mains with particular caution! 

z

 

Make sure that the available voltage is not higher than stated on the rear 

panel. 

z

 

Always plug in the power plug least. Make sure that the power-switch is set 

to off-position before you connect the device to the mains. The power-plug 

has to be accessed after installing the device. 

z

 

Make sure that the power-cord is never crimped or damaged by sharp edges. 

Check the device and the power-cord from time to time. 

z

 

Always disconnect from the mains, when the devise is not in use or before 

cleaning it. Only handle the power-cord by the plug. Never pull out the plug 

by tugging the power-cord. 

z

 

It is essential to connect the yellow/green conductor to earth. 

 

CAUTION!    Be careful with your operations. With a high voltage you   

can suffer a dangerous electric shock when touching the 
wires! 

Summary of Contents for LSE-2LRG

























Reviews: