Models SP550120T
SP440120T
Preplumbed Sewage
Pump Systems
INSTALLATION, OPERATION, & PARTS MANUAL
SAFETY INFORMATION
Carefully read and follow all safety instructions in this
manual or on pump.
This is the safety alert symbol.
When you see this
symbol on your pump or in this manual, look for one of the
following signal words and be alert to the potential for
personal injury!
warns about hazards that
will
cause serious
personal injury, death or major property damage if ignored.
warns about hazards that
can
cause serious
personal injury, death or major property damage if ignored.
warns about hazards that
will
or
can
cause
minor personal injury or property damage if ignored.
The word
NOTICE
indicates special instructions which are
important but not related to hazards.
1.
Read these rules and instructions carefully.
Failure to
follow them could cause serious bodily injury and/or
property damage.
2.
Check your local codes before installing. You must com-
ply with their rules.
Hazardous voltage. Can shock, burn, or
kill.
During operation the pump is in water.To avoid fatal
shocks, proceed as follows if pump needs servicing:
3A. Disconnect power to outlet box before unplugging pump.
3B. Take extreme care when changing fuses. Do not stand
in water or put your finger in the fuse socket.
3C. Do not modify the cord and plug. When using the cord
and plug, plug into a grounded outlet only. When wiring
to a system control, connect the pump ground lead to
the system ground.
4.
Do not run the pump dry. Dry running can overheat the
pump, (causing burns to anyone handling it) and will
void the warranty.
5.
The pump normally runs hot. To avoid burns when ser-
vicing pump, allow it to cool for 20 minutes after shut-
down before handling it.
6.
The pump is permanently lubricated. No oiling or greas-
ing is required in normal operation. for overhaul, see
instructions under “Service”.
7.
Vent sewage or septic tank according to local codes.
8.
Do not install the basin or pump in any location classi-
fied as hazardous by the United States National
Electrical Code (NEC), or by the Canadian Electrical
Code (CEC), where applicable.
PUMP SPECIFICATIONS
Power Supply Required .................................................115V
Individual Branch Circuit Required ..........................15 Amps
Motor Duty ...........................................................Continuous
Maximum Liquid Temperature...........................130°F(55°C)*
Discharge Adapter..................................................... 2" NPT
DESCRIPTION
Sta-Rite Sewage Pump Systems, Model Numbers
SP550120T and SP440120T are ideal for basement installa-
tions, pumping below-grade toilets, and laundry facilities.
Both include a submersible sewage pump, a premium heavy
duty structural foam, corrosion resistant sump/sewage basin
and lid, and a check valve for easy installation.
These submersible pumps are designed for effluent and
wastewater removal, sump drainage, dewatering and flood
control. The pumps have built in thermal overload protection
and an automatic reset. The mechanical seal and ball bear-
ings on the motor shaft are permanently lubricated.
Stainless steel hardware and a heavy duty lift out ring allow
for easy disassembly after extended use.
These basins are used for residential, commercial, and
industrial collection of sewage, effluent drainage and seep-
age water. The basin cover kit includes an inlet hub, a gas
tight cover, cord seals, gaskets, and hardware. The split
cover design of the SP5 allows for easy removal of the
pump without disturbing the vent connection. No special
tools or sealants are required.
NOTICE:
This unit is not designed for applications involving salt
water or brine! Use with salt water or brine will void warranty.
© 2005 Sta-Rite Industries
S538 (Rev. 10/14/05)
293 Wright Street • Delavan, WI 53115
Individual
Switch Setting in inches (mm)
Discharge
Model
Motor
Motor Full
Branch Circuit
Cord Length
Adapter
Number
HP
Load Amps
Required (Amps)
in ft. (m)
On
Off
Size
SC550120T
1/2
13.0
15
20 (6.1)
16 (406)
7 (178)
2"
SC440120T
4/10
12.5
15
20 (6.1)
16 (406)
7 (178)
2"
PUMP, MOTOR, SWITCH, & CORD SPECIFICATIONS
