STA-RITE J Series, Owner'S Manual

Page: 7 / 10

7
REPAIR PARTS LIST
“JB” Series With TEFC Motors - High Head
JBHBT-61H JBHCT-61H JBHDT-62H JBHET-63H JBHFT-51H
Key Part No. – JBHC3T-61H JBHD3T-62H JBHE3T-63H JBHF3T-51H
No. Description Used 1/3 HP 1/2 HP 3/4 HP 1 HP 1-1/2 HP
1* Motor - 115/230V, Single Phase 1 J218-890 J218-890A J218-891A J218-892A J218-896A
1* Motor - 230/460V, Three Phase 1 – J218-898A J218-894A J218-899A J218-900A
2 Capscrew - 3/8 - 16 x 1-1/4” Lg. 2 U30-75ZP U30-75ZP U30-75ZP U30-75ZP U30-75ZP
3 Water Slinger 1 C69-2 C69-2 C69-2 C69-2 C69-2
4 Seal Plate 1 C3-178 C3-178 C3-178 C3-178 C3-178
5 Gasket 1 C20-121 C20-121 C20-121 C20-121 C20-121
6 Shaft Seal 1 U109-118 U109-118 U109-118 U109-118 U109-118
7 Impeller - Single Phase 1 C105-93 C105-93 C105-94 C105-88 C105-92
7 Impeller - Three Phase - Also BF Models 1 C105-93A C105-93A C105-94A C105-88A C105-92A
7A Impeller Screw - Three Phase - Also BF Models 1 C30-47SS C30-47SS C30-47SS C30-47SS C30-47SS
8 Volute Assembly - With Wear Ring 1 C101-256B C101-256B C101-256B C101-256B C101-256B
8A Wear Ring (1) C23-27 C23-27 C23-27 C23-27 C23-27
9 Capscrew - 3/8 - 16 x 1-1/2” Lg. 2 U30-76ZP U30-76ZP U30-76ZP U30-76ZP U30-76ZP
10 Base - With Motor Pad 1 J204-9 J204-9 J204-9 J204-9 J204-9
10A Motor Pad (1) C35-5 C35-5 C35-5 C35-5 C35-5
11 Pipe Plug - 1/4” NPT 2 U78-57CT U78-57CT U78-57CT U78-57CT U78-57CT
12 Pipe Plug Hex Head 1 U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV
*For repair or service to motors, always give the motor Model Number and any other data found on the Motor Model Plate.
TROUBLE AND CAUSE REMEDY
FAILURE TO PUMP
1. Pump not properly primed. 1. Make sure pump casing and suction line are full of water.
See priming instructions.
REDUCED CAPACITY AND/OR HEAD
1. Air pockets or leaks in suction line. 1. Check suction piping.
2. Clogged impeller. 2. Remove and clean.
PUMP LOSES PRIME
1. Air leaks in suction line. 1. Check suction piping
2. Excessive suction lift and operating 2. Move pump nearer to water level.
too near shut-off point.
3. Water level drops while pumping, 3. Check water supply. Add length of pipe to suction
uncovering suction piping. to keep submerged end under water.
MECHANICAL TROUBLES AND NOISE
1. Bent shaft and/or damaged bearings. 1. Take motor to authorized motor repair shop.
2. Suction and/or discharge piping not 2. See that all piping is supported to relieve strain
properly supported and anchored. on pump assembly.
TROUBLE - CAUSES AND REMEDY