background image

2

HIGH RATE SAND FILTERS

To avoid unneeded service calls, prevent possible injuries, and get the most
out of your filter, READ THIS MANUAL CAREFULLY! 

The Sta-Rite Top Mounted Series High Rate Sand Filter: 
• Is designed to filter water for swimming pools. 
• Is an excellent performer; durable, reliable. 

Table of Contents

Safety Instructions .......................................................................................2-3
Dimensions/Specifications..............................................................................4
General Information .......................................................................................5
Installation ..................................................................................................5-7

Filter Mount/Piping......................................................................................5
Filter Set-up.................................................................................................6
Loading Sand Media....................................................................................6
Valve Installation.........................................................................................6
Startup/Operation........................................................................................7

Maintenance ..................................................................................................8

Water Maintenance .....................................................................................8

Storage/Winterizing...................................................................................8-10

Mult-Port Valve Service ...............................................................................9
Drain Fitting Installation/Removal .............................................................10

Troubleshooting Guide .................................................................................11
Repair Parts List.......................................................................................12-13
Pressure Drop Curve ....................................................................................14
Warranty ......................................................................................................15

READ AND FOLLOW SAFETY
INSTRUCTIONS!

This is the safety-alert symbol. When you see this symbol on your valve

or in this manual, look for one of the following signal words and be alert to the
potential for personal injury.

warns about hazards that will cause serious personal injury,

death or major property damage if ignored.

warns about hazards that can cause serious personal injury,

death or major property damage if ignored.

warns about hazards that will or can cause minor personal in-

jury or property damage if ignored.

The label NOTICE indicates special instructions which are important but not
related to hazards.

Carefully read and follow all safety instructions in this manual and on filter.

Keep safety labels in good condition.
Replace missing or damaged safety labels.

Summary of Contents for CRISTAL-FLO T-150BP-1
















Reviews: