manualshive.com logo in svg

ST STM8L1528-EVAL, User Manual, Page: 9 / 23

Share
Download
ST STM8L1528-EVAL User Manual Download Page 9

UM1000

Demonstration applications

Doc ID 17964 Rev 1

9/23

3.4.3 Setting 

the 

alarm

Use the 

ALARM

 submenu to configure the alarm seconds, minutes and hours. 

This submenu offers two options allowing to display or adjust the current alarm

.

Alarm adjust

The 

Alarm adjust

 option is similar to 

Time adjust

. 

After selecting 

Alarm adjust

,

 

or after setting the alarm, the message shown in 

Figure 10

 is 

displayed. 

Figure 10.

Alarm Adjust message

Alarm show

Select the 

Alarm show

 option to display the current alarm. After power-up, the default alarm 

time (00:00:00) is displayed till the 

Alarm adjust

 option is used to enter a new alarm time.

The following message is displayed on the LCD screen when this submenu is selected:

Figure 11.

Alarm show message

To exit from this sub menu press the joystick 

UP

.

Note:

1

When an alarm occurs, the alarm wave is played. 

2

The alarm can be used also to wake up the system from WFI or Active-halt.

Alarm Adjust

HH:MM:SS 

Alarm Show

HH:MM:SS

www.BDTIC.com/ST

Summary of Contents for STM8L1528-EVAL
























Reviews:

No comments