manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 211 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 211

RM0008

Analog-to-digital converter (ADC)

Doc ID 13902 Rev 12

211/1096

   

   

   

11.3.7 Analog 

watchdog

The AWD analog watchdog status bit is set if the analog voltage converted by the ADC is 
below a low threshold or above a high threshold. These thresholds are programmed in the 
12 least significant bits of the ADC_HTR and ADC_LTR 16-bit registers. An interrupt can be 
enabled by using the AWDIE bit in the ADC_CR1 register.

The threshold value is independent of the alignment selected by the ALIGN bit in the 
ADC_CR2 register. The comparison is done before the alignment (see 

Section 11.5

).

The analog watchdog can be enabled on one or more channels by configuring the 
ADC_CR1 register as shown in 

Table 66.

Figure 24.

Analog watchdog guarded area

         

11.3.8 Scan 

mode

This mode is used to scan a group of analog channels. 

Scan mode can be selected by setting the SCAN bit in the ADC_CR1 register. Once this bit 
is set, ADC scans all the channels selected in the ADC_SQRx registers (for regular 
channels) or in the ADC_JSQR (for injected channels). A single conversion is performed for 
each channel of the group. After each end of conversion the next channel of the group is 
converted automatically. If the CONT bit is set, conversion does not stop at the last selected 
group channel but continues again from the first selected group channel.

If the DMA bit is set, the direct memory access controller is used to transfer the converted 
data of regular group channels to SRAM after each EOC. 

The injected channel converted data is always stored in the ADC_JDRx registers.

Table 66.

Analog watchdog channel selection

Channels to be guarded by analog 

watchdog

ADC_CR1 register control bits (x = don’t care)

AWDSGL bit

AWDEN bit

JAWDEN bit

None

x

0

0

All injected channels

0

0

1

All regular channels

0

1

0

All regular and injected channels

0

1

1

Single

(1)

 injected channel 

1. Selected by AWDCH[4:0] bits

1

0

1

Single

(1)

 regular channel 

1

1

0

Single

(1)

 regular or injected channel 

1

1

1

Analog voltage

High threshold

Low threshold

Guarded area

HTR

LTR

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments