ST STLINK-V3MINIE User Manual Download Page 4

3

Development environment

STLINK-V3MINIE

 runs with an STM32 32

bit microcontroller based on the Arm

®

 Cortex

®

-M core.

Note:

Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.

3.1

System requirements

Multi

OS support: Windows

®

 10, Linux

®

 64-bit, or macOS

®

USB Type-A or USB Type-C

®

 to USB Type-C

®

 cable

Note:

macOS

®

 is a trademark of Apple Inc., registered in the U.S. and other countries and regions.

Linux

®

 is a registered trademark of Linus Torvalds.

All other trademarks are the property of their respective owners.

3.2

Development toolchains

IAR Systems

®

 - IAR Embedded Workbench

®

(1)

Keil

®

 - MDK-ARM

(1)

STMicroelectronics - STM32CubeIDE

 

1. On Windows

®

 only.

 

3.3

Firmware upgrade

The STLINK-V3MINIE tiny probe embeds firmware that needs to be frequently updated from the 

www.st.com

website to benefit from new functionality or corrections. Refer to the technical note 

Overview of ST-LINK

derivatives

 (

TN1235

) for details.

UM2910

Development environment

UM2910

 - 

Rev 2

page 4/20

Summary of Contents for STLINK-V3MINIE





















Reviews: