manualshive.com logo in svg

ST NUCLEO-F207ZG, User Manual

Share
Download
ST NUCLEO-F207ZG User Manual Download Page 27

DocID028599 Rev 7

27/82

UM1974

Hardware layout and configuration

81

6.10 

USB OTG FS or device

The STM32 Nucleo-144 board supports USB OTG or device-full-speed communication via 
a USB Micro-AB connector (CN13) and USB power switch (U12) connected to V

BUS

. 

Note:

The NUCLEO-F303ZE board supports the USB device FS only. All the other STM32 
Nucleo-144 boards support the USB OTG.

Warning:

USB Micro–AB connector (CN13) cannot power the Nucleo-
144 board. To avoid damaging the STM32, it is mandatory to 
power the Nucleo-144 before connecting a USB cable on 
CN13. Otherwise there is a risk of current injection on STM32 
I/Os. 

A green LED LD8 lights in one of these cases:

•

Power switch (U12) is ON and STM32 Nucleo-144 board works as a USB host

•

V

BUS

 is powered by another USB host when the STM32 Nucleo-144 board works as a 

USB device.

The red LED LD7 lights if overcurrent occurs when +5 V is enabled on V

BUS

 in USB host 

mode.

Note:

1. It is recommended to power Nucleo-144 board by an external power supply when using 
USB OTG or host function.
2. JP4 must be closed when using USB OTG FS.

The NUCLEO-F303ZE board does not support the OTG function but it supports USB 2.0 
full-speed, device-mode communication via a USB Micro-AB connector (CN13). USB 
disconnection simulation is implemented by PG6, which controls 1.5 K pull-up resistor (R70) 
on USB D+ line. Detection of 5 V power on USB connector (CN13) is available on PG7 
thanks to a bridge between R62 and R63 resistors. 

          

Table 10. USB pins configuration 

Pin 

name

Function

Configuration when 

using USB connector

Configuration when 

using ST morpho 

connector

Remark

PA8

USB SOF

-

-

Test point TP1

PA9

USB V

BUS

SB127 ON

SB127 OFF

Not on NUCLEO-F303ZE

PA10

USB ID

SB125 ON

SB125 OFF

Not on NUCLEO-F303ZE

PA11

USB DM

SB133 ON

SB133 OFF

-

PA12

USB DP

SB132 ON

SB132 OFF

-

PG6

USB GPIO OUT

NUCLEO-F303ZE: 
SB186 ON, SB187 

OFF 

NUCLEO-F303ZE: 

SB186 OFF 

NUCLEO-F303ZE: 

D+ pull up control 

All other Nucleo 

boards: SB186 OFF, 

SB187 ON

All other Nucleo 

boards: SB187 OFF

All other Nucleo boards:

USB power switch control

All manuals and user guides at all-guides.com

Summary of Contents for NUCLEO-F207ZG



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands