ST EVALSTPM32 User Manual Download Page 13

List of tables

Table 1.  

Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table 2.  

EVALSTPM3x evaluation board setting and configuration terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Table 3.  

J5 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 4.  

J6 SPI connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 5.  

J2 UART connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 6.  

EVALSTPM3x evaluation board parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 7.  

Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

UM1748

List of tables

UM1748

 - 

Rev 3

page 13/15

Summary of Contents for EVALSTPM32
















Reviews: