SST Automation GS11-EI User Manual Download Page 10

Page: 10 / 51

User Manual

Embedded EtherNet/IP Module

GS11-EI

3. Communication Protocol

3.1 Description

GS11-EI acts as an EtherNet/IP server at the Ethernet side, serial port use user-defind protocol. The EtherNet

/ IP communication and serial communication are completely independent, through the internal input and output

data buffer of GS11-EI to realize data exchange, according to the GS11-EI serial communication protocol, the user

board can complete the input and output data exchange.

The procedure of message transmission is as follows:

GS11-EI

user

-defined

EtherNet/IP

Request1

Request2

Request

…

Request a

Request b

Request

…

Response1

Response2

Response

…

Response a

Response b

Response

…

3.2 The GS11-EI Communication Flowchart and User Program

Here are the flowcharts of two kinds of IP configuration; users can choose one of them in accordance with

specific conditions. For the chooses of this two kinds, see also the Advanced Parameters section in chapter 6.4.

Summary of Contents for GS11-EI




















































Search results

Summary of Contents for GS11-EI

Reviews:

Related manuals for GS11-EI

Brands by name

Popular brands

SST Automation GS11-EI, User Manual

Search results

Summary of Contents for GS11-EI

Reviews:

Related manuals for GS11-EI

Brands by name

Popular brands