SSS Siedle Hi-Flow Operating & Maintenance Instructions Download Page 16

TRIPLE S HI-FLOW EXTRACTOR

LIMITED WARRANTY

The SSS Hi-Flow Extractor, which has been manufactured, tested and inspected in accordance with specific engineering requirements, is 

WARRANTED by the manufacturer to be free from defects in workmanship and materials.

This warranty is, however, subject to the following qualifications, conditions and limitations which are set forth to provide you and all  users 

of the SSS Hi-Flow Extractor with information concerning the duration, extent, availability and applicability of this Limited Warranty, the 

procedure to be taken to obtain its performance and other information concerning the manufacturer’s warranty  policy.

1. TO WHOM EXTENDED AND DURATION OF  ITEMS COVERED

This warranty extends to the original consumer purchaser from the date it 

was purchased and for the items and periods as follows:

One (1) year parts & labor unless excluded below.

2.  PARTS NOT COVERED BY WARRANTY

Certain parts of the SSS Hi-Flow Extractor require replacement in the or-

dinary course of use due to normal wear by reason of their characteristics.  

This warranty does not cover normal wear items such as electrical cables, 

carbon brushes, rubber/vinyl parts, floor brushes, hoses, tools, etc.  

3.  EXCEPTIONS AND EXCLUSIONS FROM  WARRANTY

The SSS Hi-Flow Extractor is required to be used on electric current as 

indicated on the nameplate.  Otherwise damage, defects, malfunctions or 

other failures of the SSS Hi-Flow Extractor arising from use on electric 

current not as indicated are excepted and excluded from this warranty.

Defects, malfunctions, failure or damage of the SSS Hi-Flow Extractor 

caused by improper, unreasonable or negligent use or abuse while in the 

possession of the consumer are likewise excluded from this warranty.

If repair is done on your SSS Hi-Flow Extractor by anyone other than 

those below designated as authorized to perform such work without first 

having obtained factory instructions, the manufacturer, at its sole option, 

may determine that this warranty will not apply and that reimbursement 

for such repair will not be made because of the failure to comply with such 

factory specified instructions.

4. PROCEDURE TO BE TAKEN TO OBTAIN PERFORMANCE 

OF WARRANTY

To secure repair of the SSS Hi-Flow Extractor or any warranted parts 

under this warranty, the following  procedure should be taken: 

 

The inoperative SSS Hi-Flow Extractor or warranted parts, together with 

satisfactory evidence of the purchase date, must be delivered with shipping 

and delivery charges prepaid to the Dealer from whom purchased.

If you are unable to locate the Dealer, you may write or otherwise com-

municate with 

Triple S, 2 Executive Park Drive, Billerica, MA 01862

 

for instructions before repair service is performed by anyone else.  In such 

event Triple S will provide either the location of a closely available Triple 

S Distributor Service Department or other factory instructions.

Upon compliance with the above procedure, all warranted defects will 

be repaired, at no additional charge or costs to the consumer, and the 

repaired product returned to the consumer, with all shipping and delivery 

charges prepaid.

In following the procedures above set forth PLEASE MAKE CERTAIN 

to state the Triple S model, type and serial number as shown on the name 

plate of the SSS Hi-Flow Extractor.

REPLACEMENT

In the event of the defect, malfunction or failure of your SSS  Hi-Flow 

Extractor or any warranted part to conform with this warranty, the manu-

facturer may at its sole option and own expense, replace the SSS Hi-Flow 

Extractor or any warranted part with another new identical or reasonably 

equivalent model or part in lieu of repairing the defect.

5.  NO REFUND OF PURCHASE PRICE

Triple S will not, as a matter of its warranty policy, refund the consum-

er’s purchase price.

6.

  

WARRANTY REGISTRATION CARD FOR YOUR SSS HI-

FLOW EXTRACTOR AND REQUESTS FOR INFORMATION

Please  fill  out  the  warranty  registration  card  accompanying  your  SSS 

Hi-Flow Extractor, giving complete information as requested on the card, 

and return to Triple S.

This warranty is in lieu of all other expressed or implied warranties. 

6/98

225631

Summary of Contents for Hi-Flow

















Reviews: