manualshive.com logo in svg

SSANGYONG Rexton Y290 2012, Manual

Share
Download
SSANGYONG Rexton Y290 2012 Manual Download Page 625

8810-00

1. WARNINGS FOR AIRBAG

Do not diagnose the circuit with a circuit tester. Do not attempt to modify any air bag 
components including the steering wheel, air bag mounting area, and harness.
Do not impact any air bag components including the steering wheel, air bag mounting area, 
and harness by hand or tools. You may get injured by sudden deployment.
The air bag components will be very hot after deployment. Do not touch them.
Once the air bag system is triggered, the triggered air bag assembly should be removed from 
the vehicle and replaced with new one.
The air bag contains explosive materials, so contact Ssangyong Dealer or Ssangyong 
Authorized Service Operation when trashing or replacing it.
Incorrect air bag inspection can be dangerous and cause injuries. The air bag system must be 
disposed only by Ssangyong Dealer or Ssangyong Authorized Service Operation.
Replace the steering wheel with only Ssangyong genuine part.
When the engine starts, the air bag warning lamp comes on for a system check. It goes out 
after 3 to 7 seconds when the system is normal. If this warning lamp stays ON, then the system 
may be defective. Have the air bag system checked immediately by Ssangyong Dealer or 
Ssangyong Authorized Service Operation.
The seat belt and air the bags are the most effective when you are sitting well back and upright 
in the seat.
A child restraint system must not be placed on the front seat. The infant or child can be 
severely injured by an air bag inflation in case of an accident.
Do not carry your child on your lap while driving. You cannot resist against the impact pressure 
in an accident.
The child could be crushed between you and the parts of the vehicle.
Do not place any objects on the air bag inflation location. You may get injured by those objects 
during deployment.
Do not attach any objects such as a sticker, scent bottle, or phone holder on the steering 
wheel pad and to the dashboard.
Do not put the seat cover on the front seatbacks. It may interfere with the side air bag inflation.
When sitting in the rear seat, do not hold onto the seatback of the front seat. If the side air bag 
inflates, the occupant may get seriously injured.
Do not lean on the door. When the side air bag inflates, the occupant may get seriously 
injured.
Do not place any objects such as an umbrella or a bag between the side air bag and the door. 
Do not place the part of your body near the side air bag. You may obstruct the side air bag or 
get injured by the inflation impact.

-

-

-
-

-

-

-
-

-

-

-

-

-

-

-

-

-

Summary of Contents for Rexton Y290 2012











































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands