SPX Cooling Technologies Hexacool Air Cooled Condenser none User Manual Download Page 16

16

If the minimum allowable cold process fluid temperature is estab-
lished at or near minimum heat load, it should be safe for all operat-
ing conditions.

Having  established  the  minimum  allowable  cold  water  temperature, 
maintaining that temperature can be accomplished by fan manipulation, 
as outlined in 

item 4

 under 

Fluid Cooler Operation

.

 2.  A fan operating in a forced-draft tower is subject to the risk of freez-

ing. Icing is a particular danger as this can form not only on the fan 
blades, but also the inlet guard. Ice particles can be thrown off and 
cause severe damage. The fan casing should be checked so that any 
water entering it (either from the tower or external sources) can drain 
away. If water is allowed to collect in the fan casing, the fan could be 
frozen into place. This could result in damage to the drive system if 
starting were attempted.

3.   As cold air enters the fluid cooler, it causes the falling water to be 

drawn inward. Thus, under fan operation, the lower periphery of the 
fluid cooler structure remains partly dry, seeing only random splash-
ing from within the fluid cooler—plus normal atmospheric moisture 
from the entering air. Such lightly wetted areas are most subject to 
freezing.

    Although ice is unlikely to cause structural damage, it may build up 

sufficiently to restrict the free flow of air. This effectively reduce the 
fluid  cooler's  thermal  performance  efficiency.  When  excessive  ice 
forms, stop the fan for a few minutes. With the fan off, the action of the 
spray system will cause a slight downward movement of air through 
the coil and deice the fluid cooler.

intermittent Wintertime Operation:

If  periods  of  shutdown  (nights,  weekends,  etc.)  occur  during  freezing 
weather, measures must be taken to prevent the water in the cold water 
basin—and all exposed pipework—from freezing. Several methods are 
used to combat this, including automatic basin heater systems and pump 
freeze protection systems available from Marley. 

Operation

 Caution

Summary of Contents for Hexacool Air Cooled Condenser none

































Reviews: