background image

3

To prevent injury to the user or other people and property damage, the following  instructions must be
followed. Incorrect operation due to ignoring of instructions may cause harm or damage. 

SAFETY  PRECAUTIONS

!

Always do this

Never do this

Energy Save

The air conditioner must be operated within the  temperature range indicated below:

Operating condition

Safety r ules

Suggested tools for window kit installation

1. Screwdriver(medium size Phillips)            
2. Tape measure or ruler 
3. Knife or scissors
4. Saw(In the event that the window kit needs to be cut down in size because 
     the window is too narrow for direct installation)

MODE

ROOM TEMPERATURE

COOL

62°F~95°F (17°C~35°C)

DRY

55°F~95°F (13°C~35°C)

HEAT (heating models only)

41°F~88°F (5°C~30°C)

Your air  conditioner should be used in such a way 
that it is protected from moisture. e.g. 
condensation, splashed water, etc. Do not place or 
store your air conditioner  where it can fall or be 
pulled into water or any other liquid.

Always transport your air conditioner in a vertical 
position and stand on a stable, level surface.

Turn off the product when not in use.

Always contact a qualified person to carry out 
repairs. If the power cord is damaged, it must be 
repaired by a qualified electrician.

Keep an clearance of at least 12 inches around the 
unit for proper airflow (from walls, furniture and 
curtains).

If the unit is knocked over during use, turn off  
power immediately and unplug from power source.

Never leave the unit unsupervised when in 
operation.

When unit is not in good order, please use 
common sense to prevent further damage to 
surroundings.

Do not operate your air conditioner in a wet/damp 
room such as a bathroom or laundry room.

Do not touch the unit with wet or damp hands or 
when barefoot.

Do not press the buttons on the control panel with 
anything other than your fingers.

Do not remove any fixed covers. Never use this 
appliance if it is not working properly, or if it has 
been dropped or damaged.

Never use the plug to start and stop the unit. 

Do not cover or obstruct the inlet or outlet grilles.

Do not use hazardous chemicals to clean or allow 
to come into contact with the unit. 

Do not use the unit in the presence of flammable 
substances or vapor such as alcohol, insecticides, 
petrol, etc.

Do not allow children to operate the unit 
unsupervised.

Do not use this product for functions other than 
those described in this instruction manual.

Use the unit  in the recommended room size.

Locate the unit where furniture cannot obstruct the air flow.

Keep blinds/curtains closed during the sunniest part of the day.

Keep the filters clean.

Keep doors and windows closed to keep cool air in and warm air out.

If a very hot day is expected, turn on the unit early to keep the room cool and keep the heat out.

Summary of Contents for WA-1240AE

























Reviews: