background image

UNIFIRE 

8. WARRANTY 

 
SPT Plasmateknik AB grants a warranty for its products. The warranty covers damage caused 
by faulty raw material or production errors. A faulty part will be replaced by a new one, or, if 
possible, we will repair the faulty part without cost. 
 
The warranty period is 2  years  provided the machine is used under normal conditions (one 
shift working). The torch is not covered by the warranty. 
 
The warranty does not cover damage caused by improper or careless handling, connection to 
the wrong supply voltage including voltage or frequency variations outside the specifications, 
overload, irresponsible maintenance or natural wear. 
 
Any use of non-original parts or consumables renders the warranty void. 
 
Travel costs in connection with warranty repairs or freight and packaging costs are not 
included in the warranty. 
 
Warranty repairs may only be performed by SPT Plasmateknik AB or a representative 
assigned by SPT. 
 

9. SCRAPPING 

 
Do not throw electrical equipment in the regular rubbish! According to 
EU-directive 2002/96/EG regarding waste that contains electric or 
electronic parts (WEEE) and its implementation with national laws 
products must be collected separately and brought to approved 
recycling facilities after their useful life. As the owner of the product 
you should find out the location of an approved recycling facility from 
your local dealer. 

12 

Summary of Contents for UNIFIRE 26C













Reviews: